Оценок - 3, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
. . ARGHERIT. Mode. A 112. Dimension. width 59,5 c. height 85 c. depth 53,5 c. Capacit. from 1 to 5,5 k. Electrica. connection. voltage 230/240 Volt 50 H. maximum absorbed power 1850 . Wate. connection. maximum pressure 1 MPa (10 bar. minimum pressure 0,05 MPa (0,5 bar. drum capacity 46 litr. Spinning spee. up to 1100 rp. Control program. in complianc. with IE. regulation 45. programme 2. temperature 60°C. carried out with 5,0 kg load. This appliance conforms with the following E.E.C. directives. - 73/23/EEC of 19/02/73 (Low Voltage) and subsequent modification. - 89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and subsequent modification. The washing machin. does not drain o. spin. Does the selecte. programme incorporate. water draining? Som. programmes stop at the end o. the wash cycles and drainin. will have to be selecte. manually. Is the .Rinse-Hold. function -where provided . enabled? This functio. requires manual selection fo. draining. Is the drain pump clogged. To check it, turn off the wate. supply, unplug the washin. machine and follow th. instructions on page 12, or cal. for technical assistance. Always getassistance fromauthorisedtechnicians andalways insist onoriginal spareparts. Is the drain hose kinked. The tract of the drain hos. must be as straight as possible. Make sure the drain hose is no. squashed or kinked. Is the washing machine.. drain duct clogged? Is ther. an extension of the drai. hose? If so, is it positione. incorrectly, blocking the wate. flow. Excessive vibratio. during the spin cycle. Have all transit screws bee. removed durind instal. lation? See the followin. page on installatio. procedures. Has the washing machin. been levelled correctly? Th. levelling of the applianc. should be checke. periodically. Adjust the fee. and check them with a level. Technical characteristic. Is there space between th. machine and adjacent units. If it is not a built-in model, th. washing machine will oscillat. a bit during the spin cycle. . few cm of space shoul. therefore be left around it. The washing machin. leaks. Is the metal ring of the inle. hose properly attached? Tur. off the water supply, unplu. the appliance and tr. tightening its attachmen. without forcing it. Is the detergent dispense. obstructed?. Remove an. wash it under tap water. Is the drain hose wel. attached? Turn off the wate. supply, unplug the applianc. and try tightening it. attachment. Too much foam. Is the detergent appropriat. for machine washing? Chec. whether the definition on it. label reads .for machine wash. or .hand and machine wash.. or any other similar wording. Is the correct amount bein. used? An excessive amount o. detergent, besides producin. too much foam, does no. guarantee a more effectiv. wash, and causes scaling in th. internal parts of the appliance. If, despite all checks, th. washing machine fails t. function and the proble. persists, call your neares. authorised Customer Servic. Centre, providing the followin. information. . the nature of malfunctio. . the model type no. (Mod. ..... - the serial number (S/N ..... This information can be found o. the data plate situated at the bac. of the washing machine. . Margherita - Instructions for installation and us. . ARGHERIT. Installation and remova. When Margherit. arrive. Whether new or just transported to a new house. installation is extremely important for the correc. functioning of your washing machine. After removing the applianc. from its packaging, check that i. is intact. If in doubt, contact . qualified technician immediately. The inside of the machine i. supported, for transportation, b. four screws on the back panel. Before using the washin. machine, remove the screws. remove the spacers together wit. the rubber tubes attached t. them (keeping all the parts) an. use the plastic plugs provided t. fill in the holes. Important: Use the cap (provided. to close the 3 holes which house. the stop pin, situated in the right. hand part of the lower back of th. washing machine. Levellin. The washing machine must b. levelled appropriatey in order t. guarantee its correct functioning. To level the appliance, the fron. feet must be adjusted; the angl. of inclination, measured accordin. to the worktop, must not excee. 2°. When placed on carpet, mak. sure the ventilation is not reduced. The front feet are adjustable. Retain the transit screws, spacers and washers. Should you move housethen these should bereplaced to support theinside of the machine toprevent damage whentransporting the machine. Connection to the wate. main. Both hot and cold water supplie. are preferable and they should b. between 34.5kN/m.(5lb/in.) an. 1034.2kN/m. (150lb/in.) pressure. The hose having the red end fittin. should be encountered betwee. the hot supply and the threade. connection adjacent to the lette. H on the rear of the machine. Th. hose having the white end fitting. should be connected between th. cold supply and the threade. connection adjacent to the lette. C on t...