Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
We recommend that a maintenance wash be performed on a regular basis. To run a maintenance wash: • The drum should be empty of laundry. • Select the hottest cotton wash programme. • Use a normal measure of detergent, must be a powder with biological properties. External cleaning Clean the exterior cabinet of the appliance with soap and water only, and then dry thoroughly. Important: do not use methylated spirits, solvents or similar products to clean the cabinet. Detergent dispenser drawer The detergent dispenser drawer should be cleaned regularly. 1. Remove the detergent dispenser drawer by pressing the catch downwards and by pulling it out. 28 Care and cleaning 2. To aid cleaning, the top part of the additive compartment should be removed. 3. Flush it out under a tap, to remove any traces of accumulated powder. 4. Having removed the drawer, use a small brush to clean the recess, ensuring that all washing powder residue is removed from the upper and lower part of the recess. 5. Replace the drawer and run the rinse programme without any clothes in the drum. 6. Having removed the drawer, use a small brush to clean the recess, ensuring that all washing powder residue is removed from the upper and lower part of the recess. 7. Replace the drawer and run the rinse programme without any clothes in the drum. Washing drum Rust deposits in the drum may occur due to rusting foreign bodies in the washing or tap water containing iron. Important! Do not clean the drum with acidic descaling agents, scouring agents containing chlorine or iron or steel wool. 1. Remove any rust deposits on the drum with a cleaning agent for stainless steel. 2. Run a washing cycle without any laundry to clean off any cleaning agent residues. Programme: COTTONS 95° or 90°C, press the button 6, add approx. 1/2 measuring cup of detergent. Door seal Check the door seal from time to time and remove any objects that could be trapped in the fold. Care and cleaning 29 Drain pump The pump should be inspected regularly and particularly if • the machine does not empty and/or spin • the machine makes an unusual noise during draining due to objects such as safety pins, coins etc. blocking the pump. Proceed as follows: 1. Disconnect the appliance. 2. If necessary wait until the water has cooled down. 3. Place a container close to the pump (A) to collect any spillage. 4. Release the emergency emptying hose (B), place it in the container and remove its cap. 5. When no more water comes out, unscrew the pump cover and remove it. Always keep a rag nearby to dry up spillage of water when removing the pump. 6. Remove any objects from the pump impeller by rotating it. 7. Replace the cap on the emergency emptying hose and place the latter back in its seat. 8. Screw the pump cover fully in. Warning! When the appliance is in use and depending on the programme selected there can be hot water in the pump. Never remove the pump cover during a wash cycle, always wait until the appliance has finished the cycle, and is empty. When 30 Care and cleaning replacing the cover, ensure it is securely retightened so as to stop leaks and young children being able to remove it. Water inlet filter If you notice that the machine is taking longer to fill, check that the filter in the water inlet hose is not blocked. 1. Turn off the water tap. 2. Unscrew the hose from the tap. 3. Clean the filter in the hose with a stiff brush. 4. Screw the hose back onto the tap. Emergency emptying out If the water is not discharged, proceed as follows to empty out the machine: 1. pull out the plug from the power socket; 2. close the water tap; 3. if necessary, wait until the water has cooled down; 4. place a bowl on the floor and place the end of the emergency emptying hose into the bowl. Remove its cap. The water should drain by gravity into the bowl. When the bowl is full, put the cap back on the hose. Empty the bowl. Repeat the procedure until water stops flowing out; 5. clean the pump if necessary as previously described; 6. replace the emergency emptying hose in its seat after having plugged it; 7. refit the pump cover. Care and cleaning 31 Frost precautions If the machine is installed in a place where the temperature could drop below 0°C, proceed as follows: 1. Close the water tap and unscrew the water inlet hose from the tap. 2. Place the end of the emergency emptying hose and that of the inlet hose in a bowl placed on the floor and let water drain out. 3. Screw the water inlet hose back on and reposition the emergency emptying hose after having put the cap on again. By doing this, any water remaining in the machine is removed, avoiding ice forming and consequently damage to the appliance. When you use the machine again, make sure that the ambient temperature is above 0°C. 32 What to do if... What to do if... Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without calling out an engineer. Before contacting your local Service Centre, please carr...