Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
The drain filter has not Fully screw the filter into been properly screwed on place. after cleaning. Something not working? Problem The machine vibrates or is noisy The door will not open Possible cause Solution The transit bolts have Check that the machine not been removed. has been unpacked as described in the Installation section. The feet have not been Carefully level the machine. adjusted. There is little laundry in the drum. The programme is still running. Correct operation of the machine is not affected. Wait until the end of the programme before opening the door. The water level is above the Before opening the door, bottom edge of the door. the water must be emptied out. The machine is heating the Wait until the end of the water or drying the heating or drying phase. clothes. Something not working? Problem Spinning starts late or the machine does not spin The machine will not dry or the laundry is not dry enough Possible cause The unbalance detection device that prevents excessive vibration during spinning has cut in. The water tap is not open (E10). Solution If the laundry is not evenly distributed inside the drum at the beginning of the spin cycle, the machine detects this and tries to redistribute it more evenly by means of a few drum rotations. Only when the laundry is more evenly distributed will the spin cycle be performed, at a lower speed, if the laundry is not evenly distributed. If, after about 6 minutes, the laundry is still tangled, the machine will not spin. Therefore, if the laundry is still wet at the end of the cycle, it is advisable to redistribute it manually inside the drum and to select the spin programme again. Open the water tap. The drain filter is clogged. Clean the filter. (EF0). The drying time has not Select the drying time. been selected. An appropriate drying time Select the appropriate has not been chosen. drying time suitable for the required degree of drying, according to the type of fabric (cottons or easy-cares). There is too much laundry Reduce the load. inside the appliance. Something not working? Unsatisfactory washing results If the laundry looks grey and lime scale is found in the drum • Too little detergent has been used. • An unsuitable detergent has been used. • Stubborn stains have not been treated prior to washing. • The programme/temperature has not been correctly selected. If grey stains remain on the laundry • Laundry stained with ointments, grease or oil has been washed with an insufficient amount of detergent. • The temperature selected for the wash programme was too low. • Fabric softener - especially the concentrated type - has come into direct contact with the laundry. Wash these stains immediately and pour fabric softener carefully. Foam is still visible even after the last rinse • Modern detergents often produce foam, even in the last rinse. However the laundry has been completely rinsed. White residue is left on the laundry • This is due to insoluble components in modern detergents and is therefore not the result of insufficient rinsing. Shake or brush the laundry. In future, it may be better to turn garments inside out before washing them. Check the choice of detergent; try using liquid detergents. Technical data Height x Width x Depth 82x60x54.5 cm Depth with door opened 91 cm Height adjustment ± 13 mm approx. Net weight 77 kg approx. Load (depending on programme) 4.5 kg max. Use domestic Drum speed during washing max. 55 rpm Drum speed during spinning 1200/900/700/500 rpm Water pressure 50 - 800 kPa This appliance complies with the following EC directives: -73/23/EEC of 19.2.1973 “Low voltage directive”, including directive 93 / 68 / EEC -89/336/EEC of 3.5.1989 “Electromagnetic Compatibility Directive”. Service & Spare Parts If after carrying out the necessary checks there is still a fault with your appliance please contact your local AEG Service Force Centre. In guarantee customers should ensure that the suggested checks in the “Troubleshooting” section have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown. Please note that proof of purchase is required for in-guarantee service calls. Service & Spare Parts If you require a service engineer or wish to purchase spare parts, contact your local AEG Service Force Centre, by telephoning: 08705 929 929 Help us to help you Please determine your type of enquiry before telephoning. When you contact us we need to know: 1.Your name, address and post code. 2.Your telephone number. 3.Clear and concise details of the fault. -What is the fault? -When does the fault occur? -Does the multi-display issue an error-message (E and a number)? 4.The model, production number and production identification number. 5.Date of purchase. This information can be found on the rating plate, so you have these numbers to hand we recommed you write them below. Prod. No. . . . . . . . . . . . . . . . . . . . . . Ser. No. . . . . . . . . . . . . . . . . . . . . . ....