Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
Water runs out from under the washing machine. Remove transport packaging The transport packaging has according to the installation not been removed. and connection instructions. Adjust the feet according to The machine is not level. the installation and connection instructions. There is very little washing in This does not impair the the drum (e.g. only one function. dressing gown). The water could not be completely pumped out before spinning because the drain hose is kinked or the drain pump is blocked. Check the drain hose and remove any kink if necessary, or clean the drain pump and, if required, remove foreign bodies from the pump housing. The screw connection on the Tighten the inlet hose screw inlet hose is leaking. connection Check the drainage hose and The drainage hose is leaking. replace it if necessary. The drain pump cover is not Close cover correctly. correctly closed. Stop the program and Washing is caught in the remove the washing caught door. in the door. Restart the program. The emergency emptying hose is not correctly sealed or is leaking. Seal the emergency emptying hose correctly (see section “Carrying Out an Emergency Emptying“). Call your local AEG Service Force Centre if the emergency emptying hose leaks. RINSE HOLD has been Cancel RINSE HOLD. selected. The washing machine does not spin; there is Release SOAKING button Soaking program has fin- water in the drum. (main wash program will fol ished. low). Operating Instructions Problem Possible Cause Remedy Fabric softener was not washed into machine; drawer . for conditioner is filled with water. The conditioner insert has not been correctly positioned inside the conditioner compartment or is blocked. Clean the detergent dispenser drawer and attach the conditioner insert securely. Pay attention to the maxi- Washing is heavily creased Probably too much washing was put into the drum. mum load quantity (see Program tables). In the case of easy-care fabrics, select the EASY IRON program. Washing has not been spun properly. Water is left in the drum. Drain hose is kinked. Remove the kink. Contact your local Service Maximum pump head (dis-Force Centre. For pumping charge height 1 m from the heights over 1 m a conver appliance’s base) is exceeded. sion kit is available as a special accessory. Switch off the appliance and Drain pump is blocked. pull out the mains plug. Clean the drain pump. Water tap is not fully open. Open the water tap fully. Remnants of detergent are building up in the Close the water tap. Unscrew The inlet hose filter in the the inlet hose from the water detergent dispenser coupling inlet hose at the tap and from the appliance. drawer. tap is blocked. Clean the filter. The cause is probably a No negative effect on the The rinsing water is detergent with a high silicate rinse results; use a liquid cloudy. content. detergent if necessary. Door cannot be Door is locked for safety rea- Wait for 1 or 2 minutes after opened. sons. the end of the program. Operating Instructions If the washing results are not satisfactory If the washing turns greyish and limescale deposits are present in the drum • Insufficient detergent has been added. • Incorrect detergent was used. • Stains were not pre-treated. • Program or temperature was not set correctly. • If using modular detergents, the individual components were not used in the correct ratio. If there are still grey stains on the washing • Soiled garments with ointments, grease or oils were washed with insufficient detergent. • The temperature selected for the wash was too low. • A frequent cause is that fabric softener - particularly a concentrated one - has come into contact with the washing. Wash out these types of stains as soon as possible and use the fabric softener carefully. If after the last rinse foam is still visible • Modern detergents can still cause foam in the final rinse cycle. However, the washing is still sufficiently rinsed. If there are white residues on the washing • These are insoluble contents of modern detergents. They are not the result of an insufficient rinse. Shake out the washing or brush it off. Turn the washing inside out before washing it. Review your choice of detergent and if necessary use liquid detergent. Operating Instructions Carrying out an emergency emptying • If the washing machine no longer pumps out the water, emergency emptying must be carried out. • If the washing machine is located in a room in which below freezing temperatures might occur, emergency emptying must be carried out. Furthermore: unscrew the inlet hose from the water tap and drain off the water. Empty the drainage hose. 1 Warning! Switch off the washing machine and pull out the mains plug prior to performing emergency emptying. Warning! The water, which flows out of the emergency emptying hose can be hot. First allow the water to cool down before you carry out the emergency emptying. 0 1. Have a flat container on hand to catch the water. 2. Pull down the flap in the right corner...