Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
. Allow 2 inches of space between the back and sides of the appliance. . Put your laundry into the washer evenly. Uneven laundry may cause noise or vibration. . DO NOT use excessively hot water (122.F / 50°C or more). Plastic parts may be deformed or damaged. Also, clothing may be deformed or bleached. . Before washing, check all pockets. If nails or pins remain in pockets, they may damage the washer or clothes. . Never splash water on the control panel. . Plug the washer into an exclusive properly installed-grounded wall outlet. Do not under any circumstances cut or remove the third (ground) prong from the power cord. Any questions concerning power and/or grounding should be directed toward a certified electrician or an Authorized Avanti Products service center. SELECTING A LOCATION Before you install the portable washer, select a location with the following characteristics: . A hard level surface (if the surface is uneven, see Adjusting The Adjustable Foot section on the next page). . Away from direct sunlight. Direct sunlight may affect the acrylic coating, plastic and electrical components. . Adequate ventilation. . Away from sources of heat such as coal or gas. Make sure that the washing machine does not stand on its power cord. . Ventilation openings must not be obstructed by carpeting when the portable washer is installed on a carpeted floor. It is recommended that you place your portable washer on a hard material floor such as tile, concrete, linoleum and to avoid if at all possible placement on wooden floors or carpeted areas. 9 10 INSTALLING THE NOISE DAMPER PLATE CONNECTING THE WATER SUPPLY HOSES The water supply hose must be connected to the washing machine at one end and to the water faucet at the other. Do not stretch the water supply hose. If the hose is too short and you do not wish to move the water faucet, replace the hose with a longer, high-pressure hose. Select appropriate faucet as shown in the figures below. If none of these faucets are available, use the faucet adapter provided. The end of faucet spout should be longer than 10mm (0.4”), or the connector cannot be fixed properly. Water leakage could develop. 1. Connect the water inlet hose to the faucet by turning the connecting nut. 2. Then connect the other end of water inlet hose to the cold connector in water mixing valve by turning the connecting nut. Rubber ring seal Be sure a rubber ring is inside the connecting nut. WATER INLET HOSE CONNECTING NUT COLD WATER CONNECTOR LID OF HOT WATER CONNECTOR CONNECTING NUT If you have both cold and hot water supplied, connect the inlet hoses by matching cold to cold and hot to hot. 1. Connect the water inlet hoses to the faucets by turning the connecting nuts. 2. Unscrew the lid of hot water connector in water mixing valve, and then connect the other end of water inlet hoses to the connectors in water mixing valve by turning the connecting nuts. WATER INLET HOSE WATER INLET HOSE CONNECTING NUT COLD WATER CONNECTOR HOT WATER CONNECTOR CONNECTING NUT CONNECTING NUT Be sure the rubber rings are inside the connecting nuts. SINK FAUCET CONNECTION For normal kitchen-sink tap only use the inlet hose with cold water inlet. Connect the inlet hose to the male hose thread adapter by turning it clockwise to be fixed tightly. Make sure to insert the rubber ring enclosed. Then connect tightly to your sink. Note: Some faucets may require you to also use the female hose thread adapter between the male adapter and your sink faucet as shown below. Make sure the rubber ring is inserted and connect to your sink. If water leaks from faucet connection or washer connection, turn off water and tighten fully using a wrench. Be careful not to over tighten and damage water connection. Turn on water supply and make sure no leaks are present. DISCONNECTING THE WATER SUPPLY HOSES Dismantling the hose directly may cause water to splash due to the possible high water pressure in the hose, even after the faucet has been turned off. Please take off the hose as per following steps, even if the faucet is closed: . Turn off the faucet. . Turn on the power and let the machine run for about 5 seconds then turn it off. . Remove the connecting nuts from the faucet and washing machine. CONNECTING NUT Note: If the washing machine is frequently used, it is not necessary to dismantle the inlet hose to avoid possible damage to the screws. NOTE: The highest point of the drain hose must be in the height of 2.25 – 4 feet POSITIONING THE DRAIN HOSE Connect the drain hose to the water outlet of the washing machine then fasten it with the included spring clamp. Since only up drainage is available, drain hose can be hung in the basin or bathtub. above floor level, otherwise, the washer cannot work normally. 11 • ELECTRICAL CONNECTION .Warning• Improper use of the grounded plug can result in the risk of electrical shock. If the power cord is damaged, have it replaced by an authorized Avanti Products service center. This appliance should be pro...