Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
to the sink. – Power cord. Moisture in the drum is due to the final inspection which every washer-dryer undergoes before it leaves the factory. Depending on the connection situation, the following part is also required: – 1 hose clip O 24-40 mm (DIY store) is also required for connection to a siphon. The bag contains: – Covers for holes left by removing the transport bolts. 54 Useful tools The following tools are helpful: – Box wrench A/F 13 for removing the transportation bolts. – Spirit level for aligning the washer-dryer. Dimensions a = 600 mm b = 560 mm c = 850 mm Weight 67 kg Installation surface Appliance stability is important so that the washer-dryer does not "wander" during the spin cycles. The installation surface must be solid and level. Soft floor coverings, e. g. carpets or floor coverings with a foam backing are not suitable. If the washer-dryer is to be installed on a wooden floor: ¦ If possible, install the washer-dryer in a corner. ¦ Screw a water-resistant wooden board (at least 30 mm thick) to the floor. ¦ Secure the washer-dryer feet with fixing brackets*. If the washer-dryer is to be installed on a base: ¦ Secure the washer-dryer feet with fixing brackets*. * Holding brackets (set) can be obtained from a specialist store or the Customer Service, order no. WMZ 2200. Removing the transportation protection devices m Caution The transport bolts must always be removed before using the appliance for the first time and must be retained for any subsequent transport (e.g. when moving). ¦ Release all screws A using the A/F 13 wrench until they can be moved freely. ¦ Remove the four spacers. They will fall to the floor when you tip the machine. B A ¦ Insert the covers. D C Built-under or built-in appliance installation The appliance must be built under or built in prior to connecting the power supply. The appliance can be built into or under a kitchen work surface. For this purpose, a recess width of 60 cm is required. ¦ The washer-dryer must only be installed under a one-piece worktop that is permanently attached to the surrounding cabinets. Caution For safety reasons in built-under installation, a cover plate* must be assembled by a specialist in place of the appliance cover plate. * Cover plate (set) can be obtained from a specialist store or the Customer Service, order no. WMZ 2420. Hose and cable lengths Connection on left side mcmax.100mcmax.100110cm~~ 100cm~~ 110cm~~ Connection on right side Other hoses Available from specialist dealers: – Extended supply hose (approx. 2.20 m). mcmax.100mcmax.100150cm~~ 140cm~~ 150cm~~ Connecting the water m Risk of electric shock! To prevent leaks or water damage, it is essential to follow the instructions in this chapter! Water inlet hose Caution Operate the washer-dryer with cold drinking water only. Do not connect to the mixer tap of an unpressurised hot-water apparatus. If in doubt, have the appliance connected by a specialist. Do not use a used inlet hose. Only use the inlet hose supplied or one which was purchased from an authorised specialist dealer. The water inlet hose must not be – kinked or crushed, – modified or severed (strength is no longer guaranteed). Plastic threads must only be tightened by hand. Do not remove the strainers from the water supply hose. Check the mains water pressure: – The water pressure should be between 1 and 10 bars (when the tap is turned on, at least 8 litres of water is discharged per minute). – If the water pressure is higher, install a pressure reducing valve. Connect the water supply hose ¦ to the rear panel of the washer-dryer and ... min. 10 mm ¦ to the tap. ¦ After connecting the water inlet hose: Turn on the water tap completely, and check connection points for water-tightness. Water drainage hose m Warning Do not bend or pull the water drainage hose. Height difference between the placement area and drainage point: maximum 100 cm. Drainage into a siphon: ¦ Secure connection point with 24-40 mm O hose clip (specialist outlet). Drainage into a wash basin: Caution The plug must not block the drain of the wash basin. ¦ Secure the drainage hose to prevent it from slipping out of the sink. ¦ When the water is being pumped out of the washer-dryer, check that the water drains away quickly enough. Aligning the washer-All four appliance feet must be firmly on the ground. dryer The washer-dryer must not wobble. Level the washer-dryer with the assistance of the four adjustable feet and a spirit level: ¦ Loosen the lock nut 1 using the wrench. ¦ Adjust the height by rotating the foot 2. ¦ Tighten the lock nut 1 against the housing. Connecting the power m Caution Connect the washer-dryer only to an alternating current via a correctly installed earthed socket. The mains voltage must correspond to the voltage specification on the washer-dryer (nareplate). Connection specifications as well as the required fuses are stipulated on the appliance nameplate. Ensure that: – The mains plug and socket are compatible. – The cable cross...
Эта инструкция также подходит к моделям:Стиральные машины - WVD24460GB/02 (2.22 mb)
Стиральные машины - WVD24460GB/03 (2.22 mb)
Стиральные машины - WVD24460GB/04 (2.22 mb)
Стиральные машины - WVD24460GB/05 (2.22 mb)