Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
. (Rinse hold = no final spin) selected? a page 3, 4. . Can be opened by emergency release only? a page 13. Programme does not start. . (Start/Add laundry) pressed or (Finished in) time selected? . Washing machine door closed? . Childlock active? Deactivate a page 5. Detergent solution is not emptied. . (Rinse hold = no final spin) selected? a page 3, 4. . Clean the detergent solution pump a page 11. . Clean drain pipe and/or drain hose. Water not visible in the drum. . Not a fault -water below the visible area. Spin result not satisfactory. Laundry wet/too damp. . Not a fault -imbalance monitoring system has cancelled spinning, due to uneven laundry distribution. Distribute large and small items of laundry evenly in the drum. . w (Easy-Iron) selected? a page 5. . Speed selected too low? a page 5. The programme duration changes during the wash cycle. . Not a fault -the programme cycle is optimised for the particular washing process. That can lead to alterations in the programme duration in the display panel. Repeated spin start-up. . Not a fault -imbalance system is equalising the imbalance. Residual water in the 0 compartment for care products. . Not a fault -the action of the care product is not affected. . Clean the insert if necessary a page 10. Odour formation in the washing machine. . Run the E Cottons 90 °C programme without any laundry. Use standard detergent. Status indicator t flashes. Foam may run out of the detergent drawer. . Too much detergent used? Mix 1 tablespoon of fabric softener with . litre of water and pour into compartment II (not for outdoor, sports and down-filled textiles!). . Reduce the detergent dosage for the next wash cycle. Pronounced generation of noise, vibration and "wandering" during spinning. . Are the appliance feet fixed? Secure appliance feet a Installation instructions. . Transportation safety devices removed? Remove transportation safety devices a Installation instructions. Noises during spinning and emptying. . Clean the detergent solution pump ..page 11. Display panel/indicator lamps do not function during operation. . Power cut? . Circuit breakers tripped? Switch circuit breakers back on or replace. . Energy saving mode active? . If the fault recurs, call our after-sales service. Programme cycle longer than usual. . Not a fault -the imbalance monitoring system is equalising the imbalance by repeatedly redistributing the laundry. . Not a fault -foam detection system active -adds an additional rinse cycle. Detergent residue on the laundry. 12 . In isolated cases, phosphate-free detergents contain water-insoluble residues. . Select m Rinse/Spin or brush down the laundry after washing. 13 What to do if... ..In Add laundry mode, ..(Start/Add laundry) flashes very quickly and a signal sounds. . Water level too high. Not possible to add laundry. Close the washing machine door immediately if necessary. . To continue the programme, press ..(Start/Add laundry). If you cannot correct a fault yourself (switching on/off) or a repair is required: . Set the programme selector to Off and pull the mains plug out of the socket. . Turn off the tap and call our after-sales service ..page 13. Emergency release e.g. in the event of a power failure The programme will continue running when the power supply has been restored. However, if the laundry has to be removed, the washing machine door can be opened as follows: Risk of scalding. The detergent solution and laundry may be hot. It may be necessary to first let the laundry cool down. Do not reach into the drum if it is still rotating. Do not open the washing machine door if water can be seen through the glass. 1.Set the programme selector to Off and pull out the mains plug. 2.Empty the detergent solution ..page 11. 3.Pull the emergency release downwards with a tool and release. Washing machine door can then be opened. After-sales service ..If you cannot remedy the fault yourself (What to do if ... , ..page 12, 13), please contact our after-sales service. We will always find a suitable solution to avoid unnecessary visits by repair personnel. ..The contact details of your nearest after-sales service can be found here or in the after-sales service directory (depending on model). . GB 0844 8928999 (Calls from a BT landline will be charged at up to 3 pence per minute. A call set-up fee of up to 6 pence may apply). . IE 01450 2655 ..Please give the after-sales service the product number (E-Nr.) and the production number (FD) of the appliance. Product number Production number This information can be found: on the inside of the washing machine door*/opened service flap* and rear of the appliance. *depending on model ..Trust the manufacturer's technical expertise. Turn to us. You will thereby ensure that the repairs are performed by trained service personnel equipped with original spare parts. Observe the safety instructions on page 8. Washing machine Instruction manual en Do not operate this washing machine until you have read these instructi...
Эта инструкция также подходит к моделям:Стиральные машины - WM14S363DN/07 (1.39 mb)