Войти:
Оценок - 0, средний балл: 0 ( )

Инструкция по эксплуатации Bosch, модель WM11E26GBC/03

Производитель: Bosch
Размер: 1.55 mb
Название файла:
Язык инструкции:en
Перейти к скачиванию



К этому устройству также есть другие инструкции:

Фрагмент инструкции


1. Loosen the hose clamp, carefully remove the drainage hose (residual water). 2. Clean the drainage hose and siphon connecting piece. 3. Reattach the drainage hose and secure the connection with the hose clamp. Filter in the water supply Risk of electric shock Do not immerse the HydroSafe safety device in water (contains an electric valve). Reduce the water pressure in the supply hose: 1. Turn off the tap. 2. Select any programme (except ....................../ ........../..........(Rinse/ Spin/Drain)). 3. Select ..(Start/Pause). Let the programme run for approximately 40 seconds. 4. Turn the programme selector to ......... (Off). Disconnect the mains plug. Clean the filter: 1. Depending on model: Disconnect the hose from the tap. Clean the filter using a small brush. and/or for Standard and HydroSafe models: Remove the hose on the rear of the appliance, Remove the filter with pliers and clean. 2. Connect the hose and check for leaks. Risk of scalding. Allow the detergent solution to cool down. Turn off the tap. instructions on page 8. Electricity Programme Load Water*** consumption*** duration*** 6 kg 0.51 kWh 55 l 2:21 h 6 kg 0.63 kWh 55 l 2:21 h 6 kg 1.26 kWh 55 l 2:29 h Consumption values Programme ..................(Cottons) 30 °C** ..................(Cottons) 40 °C** ..................(Cottons) 60 °C** ..................(Cottons) ....ecoPerfect 60 °C* ..................(Cottons) 90 °C ....................(Easy-care) 40 °C** C......a....oe ..........(Quick/Mixed fabrics) 40 °C** ......................, ................(Delicates cold) ......................(Delicates) 30 °C ............................(Wool cold) ............(Wool) 30 °C * Programme setting for testing and energy labelling in accordance with EU directive 92/75/EEC. ** Programme setting for testing in accordance with valid standard EN60456. Note on comparative tests: For testing the test programmes, wash the specified load using the maximum spin speed. As a short programme for coloureds, select the programme C......a....oe .......... (Quick/Mixed fabrics) 40 °C with the maximum spin speed. *** The values deviate from the indicated values depending on water pressure, hardness, and inlet temperature, ambient temperature, type, amount and soiling of the laundry, detergent used, fluctuations in the power supply and selected additional functions. Washing 6 kg 1.02 kWh 45 l 2:49 h 6 kg 1.98 kWh 59 l 2:34 h machine 3 kg 0.55 kWh 55 l 1:37 h 3 kg 0.48 kWh 32 l 1:03 h 2 kg 0.06 kWh 31 l 0:41 h 2 kg 0.21 kWh 31 l 0:41 h 2 kg 0.10 kWh 39 l 0:40 h 2 kg 0.19 kWh 39 l 0:40 h What to do if ... . Water is leaking out. – Attach/repl– Tighten the ace the drainage hose correctly. screw connection of the supply hose. . No water supply. Detergent not dispensed. – (Start/P– Tap not tur– Filter block– Supply hosnause) not selected? ed? Clean the filter –> page 10. e kinked or trapped? ed on? . Washing machine door cannot be opened. – Safety funct– ----(withoion active. Wait approx. 2 minutes. ut final spin) selected? –> page 3, 4. . Programme does not start. – (Start/P– Washing m– Childproof lause) or (Finished in-time) selected? achine door closed? ock active? Deactivate –> page 5. . Detergent solution is not drained. – ----(witho– Clean the d– Clean the wut final spin) selected? –> page 3, 4. etergent solution pump –> page 10. aste pipe and/or drainage hose. . Water not visible in the drum. – Not a fault water below the visible area. . Unsatisfactory spin result. Laundry wet/too damp. – Not a fault the spin cyDistribute s– Programme– Selected spthe unbalanced-load detection system has cancelled cle because of uneven distribution of the laundry. mall and large items of laundry evenly inside the drum. ..A......c.......(Easy-iron) selected? –> page 7. eed too low? ..page 5. . The programme length jumps during the final spin.. – Not a fault varying distdisplay panthe number of spin cycles may be changed due to the ribution of the laundry, which may cause the time in the el to be corrected. . Spin cycle performed several times. – Not a fault imbalance. unbalanced load detection system adjusts the . Residual water in the compartment for care products. – Not a fault – Clean the inthe action of the care product is not affected. sert if necessary –> page 9. . Odour formation in the washing machine. – Run prograUse standard detergent. mme ... ........... (Cottons) 90 °C without laundry. . Foam escaping from the detergent drawer. – Too much dIf foam is eMix 1 tablesinto compa– Reduce the etergent used? scaping from the detergent drawer: poon of fabric softener with . litre of water and pour rtment II (not with outdoor or down fabrics). detergent dosage for the next wash cycle. . Intense noise formation, vibrations and “wandering” during the spin cycle. – Are the appSecure the – TransportatRemove the instructions. liance feet fixed? appliance feet –> Installation instructions. ion safety devices removed? transportation safety devices –> Installation . Display panel/in...

Эта инструкция также подходит к моделям:
Стиральные машины - WM11E26GBC/04 (1.55 mb)
Стиральные машины - WM11E26GBC/08 (1.55 mb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории