Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
– Before using the appliance for the first time, ensure that all transport safety bolts have been removed and kept safe for any subsequent transport. – If you need to transport the appliance at a later date, always refit the transport safety bolts to prevent damage to the washer- dryer. – Appliance stability is essential to ensure that the washer dryer does not Positioning and “creep” during spin cycles. levelling – The installation area must be firm, clean and level. – Parquet floors and soft floor coverings, e.g. carpets or foam-backed floor coverings, are unsuitable. Positioning Slide sheets facilitate the insertion of the washer-dryer into the installation space. These can be ordered from the after-sales service, spare part no. 66 1827. Moisten the slide sheets with a mixture of water and washing-up liquid before sliding the washer-dryer into place. Do not use grease and/or oil. Intense noise, vibrations and “wandering” may be the result of incorrect Levelling levelling. – All four appliance feet must stand firmly on the ground. – The washer-dryer must not wobble. – Check the levelness of the washer-dryer with a spirit level and correct if necessary. – The washer-dryer must not rest against the sides of the installation recess. – The lock nuts of the front appliance feet must be screwed tightly against the housing. . Dimensions Width x depth x height 595 mm x 584 mm x 820 mm Weight 85 kg Hose and cable lengths Left-hand connection or Right-hand connection approx. 1350 min. 500 max. approx. 1400 900 Water connection Water supply * depends on the model approx. 1400 approx. 1000 approx. 760 min. 500 approx. 950 max. 900 Dimensions in mm To prevent leaks or water damage, you must observe the instructions in this section. If in doubt, have a technician connect the appliance. The water supply and drain hoses can be routed to the left of right, depending on installation conditions. Do not use a used inlet hose. Only use the inlet hose supplied or one which was purchased from an authorised specialist retailer. Do not allow the water supply hose to be: – kinked or squashed, – altered or cut (strength no longer guaranteed). Note the water pressure in the mains supply: The water pressure should be between 50-900 kPa (0.5-9 bar) (at least 8 litres of water flow out per minute when the tap is turned on). If the water pressure is higher, a pressure reducing valve must be fitted. Connect the cold-water supply hose (blue union nut) to the cold water tap with ." pipe (3/4" = 26,4 mm) thread. Only tighten plastic screw connections by hand. Do not remove the filter from the supply hose. After connecting the water supply hose: – Turn the tap on fully. – Check the connections for leaks. Water drainage Drainage into a siphon Electrical connection Fitting the door hinges to the washer-dryer – Do not kink the drain hose or pull it lengthways. – Height difference between the installation surface and the drain: max. 90 cm, min. 50 cm. Secure the connection with the 24-40 mm hose clamp (included with the appliance). The washer-dryer must only be connected to an alternating current supply via a properly installed earthed socket. If a residual current circuit breaker is used, only use a type which displays this symbol: ‚. Only this symbol guarantees compliance with the currently applicable regulations. The mains voltage must match the voltage specifications on the washer- dryer (rating plate). The connected load and fuse required are shown on the rating plate. Make sure that: – the mains plug fits the socket. – the cable cross-section is adequate. – the earthing system is properly installed. – the appliance is not standing on the mains cable. – the mains plug is accessible at all times. Changes to the mains cable may only be carried out by an electrician. Do not use multiple plugs/adapters or extension cables. Do not plug in or unplug the mains plug with wet hands. Only pull the mains plug out by the plug itself. Once the washer-dryer has been installed in a kitchen unit, it can be concealed with a door. If you wish to do this, you must fit the hinges supplied to the washer-dryer. Table of programmes Observe the information on care labels, fabric type and load quantity. Type of laundry Options* Drying Programmes* °C max. T X Q Z R 5 ‰ Cottons ; c 30- 90 6 kg/ 4kg* * Hard-wearing fabrics, heat-resistant fabrics made of cotton or linen. G G G G G G A Easy-Care = 30- 40 Easy-care fabrics made of cotton, linen, synthetic fibres or blended fabrics. G G A G G A G Mixed Load ;= c 30 3kg Fabrics made from cotton or easy-care fabrics. G G G G G A G Delicate/Silk , 30 2kg For delicate, washable fabrics, e. g. made of silk, satin, synthetic fibres or blended fabrics (e.g. curtains). A G A G A A A Wool W cold-30 Suitable for hand or machine-washable fabrics made from wool or a wool blend. A A A A A A A *Programmes and options depend on the model **Reduced load quantity for successive washing and drying programme Consumption rates Washing Progr...
Эта инструкция также подходит к моделям:Стиральные машины - WKD28320EU/02 (750.73 kb)
Стиральные машины - WKD28320EU/03 (750.73 kb)