Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
12 What to do if... .. Water is leaking out. . Attach/replace the drainage hose correctly. . Tighten the screw connection of the supply hose. .. No water supply. Detergent not dispensed. . .. Start/Pause not selected? . Tap not turned on? . Filter blocked? Clean the filter .. page 11. . Supply hose kinked or trapped? .. Washing machine door cannot be opened. . Safety function active. Programme termination? .. page 4. . Rinse Stop (without final spin) selected? .. page 3,4. . Can be opened by emergency release only? .. page 13. .. Programme does not start. . .. Start/Pause time selected? . Washing machine door closed? .. Detergent solution does not empty. . Rinse Stop (without final spin) selected? .. page 3,4. . Clean the detergent solution pump .. page 11. . Clean the waste pipe and/or drainage hose. .. Water not visible in the drum. . Not a fault - water below the visible area. .. Spin result not satisfactory. Laundry wet/too damp. . No fault - the unbalanced-load detection system interrupted spinning, uneven laundry distribution. Distribute large and small items of laundry evenly in the drum. . Easy-iron selected? .. page 5. . Speed selected too low? .. page 5. .. Drum spins gently several times. . Not a fault - unbalanced-load detection system is adjusting the imbalance. .. Residual water in the .. compartment for care products. . Not a fault - the action of the care product is not affected. . Clean the insert if necessary .. page 10. .. Odour formation in the washing machine. . Run programme .... Cottons 90 °C without laundry. Use standard detergent. .. Wash display lamp flashes. Detergent may be leaking out of the detergent drawer. . Too much detergent used? Mix 1 tablespoon of fabric softener with . litre of water and pour into compartment II (not with outdoor or down fabrics). . Reduce the detergent dosage for the next wash cycle. .. Loud spinning, vibrations and .wandering. during the spin cycle. . Are the appliance feet fixed? Secure appliance feet .. Installation instructions. . Transportation safety devices removed? Remove transportation safety devices .. Installation instructions. .. Noises during spin and drain cycles. . Clean detergent-solution pump .. page 10. .. Indicator lamps do not function during operation. . Power cut? . Circuit breakers tripped or fuses blown? Reset the circuit breakers or change the fuses. . If the fault occurs repeatedly, call the after-sales service. .. Programme Status longer than usual. . Not a fault - unbalanced-load detection system is adjusting the imbalance by repeatedly redistributing the laundry. . Not a fault - foam detection system active - adds an additional rinse cycle. .. There are detergent residues on the laundry. . Occasionally, phosphate-free detergents contain water-insoluble residues. . Select .. SuperQuick 15. or brush the laundry after washing. 13 What to do if ... .. In pause mode, .. Start/Pause flashes very quickly and a signal sounds. . Water level too high. Not possible to add more laundry. Close the washing machine door immediately if necessary. . To continue, press the .. Start/Pause button. If you cannot correct a fault yourself (switching on/off) or a repair is required: . Turn the programme selector to Off and remove the mains plug from the socket. . Turn off the water supply and call the after-sales service ....page 13. Emergency release e.g. in the event of a power cut The programme continues when the power supply is restored. However, if the laundry has to be removed, the washing machine door can be opened as follows: Risk of scalding The detergent solution and laundry may be hot. If possible, leave to cool down. Do not reach into the drum if it is still turning. Do not open the washing machine door if you can see water through the glass. 1. Turn the programme selector to Off and disconnect the mains plug. 2. Drain the detergent solution .. page 10. 3. Pull the emergency release downwards with a tool and release. Washing machine door can then be opened. After-sales service .. If you cannot remedy the fault yourself (What to do if ..., ....page 12, 13), contact our after- sales service. We will always find a suitable solution to avoid unnecessary visits by repair personnel. .. . You will find the contact data for your closest after-sales service in the after-sales service directory (depending on model). . GB 0844 8928979 (Calls from a BT landline will be charged at up to 3 pence per minute. A call set-up fee of up to 6 pence may apply). . IE 01450 2655 .. Please give the after-sales service the product number (E no.) and the production number (FD) of the appliance. Product number Production number This information can be found: on the inside of the washing machine door*/ opened service flap* and rear of the appliance. *depending on model .. Trust the manufacturer's competence. Turn to us. You will thereby ensure that the repairs are performed by trained service personnel equipped with original repair parts. Instruction manual Washin...