Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
Clothes are soaked more quickly and thoroughly during wash cycle. The detergent suds can be removed more easily by the water shower during rinse cycle. The water circulation system uses both water and detergent more efficiently. Built-in Heater Internal heater automatically heats the water to the best temperature on selected cycles. Child Lock The Child lock prevents children from pressing any button to change the settings during operation. More economical by Intelligent Wash System Intelligent Wash System detects the amount of load and water temperature, and then determines the optimum water level and washing time to minimize energy and water consumption. Low noise speed control system By sensing the amount of load and balance, it evenly distributes load to minimize the spinning noise level. Safety device (Aqua lock) Aqua lock System is designed for detecting water leak during operation to prevent water from flooding over the floor. Steam Washing and Refresh Steam Washing features upgraded washing performance with low energy consumption. Refresh cycle reduces wrinkles from dry clothes. Automatic Wash Load Detection Automatically detects the load and optimizes the washing time. ...., .., 4 S pecification Drawer Inlet hose(1EA) Spanner Accessories . The appearance and specifications may be varied without notice to raise the units quality. Name : Front loading washing machine Power supply : 220-240V~, 50Hz Size : 600mm(W)x 590mm(D) x 850mm(H) Weight : 63kg Max.Watt : 2100W (Wash) / 1100W (Steam) Wash capacity : 8,0kg Water consumption : 52.( 6,5./ kg ) Permissible water pressure : 0,3-10kgf/cm2 (30-1000 kPa) Spin speed : /400/600/800/1000/1200/1400 I nstallation • Installation place requirement Level floor : Allowable slope under entire washer is 1° Power outlet : Must be within 1.5 meters of either side of location of washer. Do not overload the outlet with more than one appliance. Additional Clearance : For wall, door and floor modeling is required. (10cm : rear /2cm:right & left side) Do not place or store laundry products on top of washer at any times. They can damage the finish or controls. • Positioning Install the washer on a flat hard floor. Make sure that air circulation around the washer is not impeded by carpets, rug etc. • Never try to correct any unevenness in the floor with pieces of wood, cardboard or similar materials under the washer. • If it is impossible to avoid positioning the washer next to a gas cooker or coal burning stove, an insulation(85x60cm) covered with aluminum foil on the side facing the cooker or stove, must be inserted between the two appliance. • The washer must not be installed in rooms where the temperature can drop below 0°C. • Please ensure that when the washer is installed, it is easily accessible for the engineer in the event of a breakdown. • Adjust all four feet using the transit bolt spanner provided ensuring the appliance is stable, and a clearance of approximately 20mm is left between the top of the washer and the underside of the work-top. 6 nstallation 8 I Normal Tap without thread & screw type inlet hose Normal Tap without thread & one touch type inlet hose 1. Unscrew the fixing screw to attach the tap. 2. Push the connector up till the rubber packing is in tight contact with the tap. Then tighten the 4 screws. 3. Push the water supply hose vertically upwards so that the rubber packing within in the hose can adhere completely to the tap and then tighten it by screwing it to the right. 1. Untighten the upper connector screw. 2. Push the upper connector up till the rubber packing is in tight contact with the tap. Then tighten the 4 screws. 3. Connect the water supply hose to the middle connector, pushing the plate down. • Make sure that there are no kinks in the hose and that it is not crushed. • Make sure that the rubber seal is inside the hose connector. • In case the diameter of the tap is large remove the guide plate. • Unable water Tap for connectoring hose. • Turn the middle connector not to have water leaked. • To separate the water supply hose from the middle connector shut off the tap. Then pull the inlet hose down, pushing the plate down. 10 I nstallation Level adjustment Concrete floors Wooden floors (Suspended floors) 1. Adjusting the washing machine level properly prevents excessive noise and vibration. Install the appliance on a solid and level floor surface, preferably in a corner of the room. 2. If the floor is uneven, adjust the adjustable feet as required. (do not insert pieces of wood etc. under the feet) Make sure that all four feet are stable and resting on the floor and then check that the appliance is perfectly level. (use a spirit level) . After the washer is level, tighten the lock nuts up towards of the base of the washer. All lock nuts must be tightened. . Diagonal Check When pushing down the edges of the washing machine top plate diagonally, the machine should not move up and down at all. (Please, check both of tw...