Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
This plastic strip and the cones must be removed. To do this, simply peel away the tape on the bottom sides of the unit that hold the plastic strip and cones in place. NOTE: Failure to remove these cones will likely cause the unit to vibrate excessively during the spin cycles. 3. The drum on both models is locked in position. Loosen the four locking bolts and remove them along with the plastic spacers (Fig. 1). NOTE: If the plastic spacers cannot be removed, open the side panel by loosening the screws indicated as “V” in Fig. 1. Remove the spacers and replace the panel. 4. Next, loosen the two locking screws (Z) and remove the two pins (U), as illustrated in Fig. 2. Keep the bolts, screws and pins for future use. 5. Plug the holes with the plastic plugs provided with the unit (packed inside the drum with the documentation) (Fig. 3). 6. To level the machine, adjust the feet by screwing or unscrewing as needed. Once the machine is level, tighten the locknuts (Fig. 4). V FIG. 1 FIG. 3 FIG. 4 ELECTRICAL CONNECTION ELECTRICAL CONNECTION Grounding Instructions This appliance must be grounded. In the case of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. WARNING! Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded. Do not modify the plug provided with the appliance. If it will not fit the outlet, have a proper outlet installed by a qualified electrician. If the power supply cord is damaged in any way please contact the dealer. Position the appliance so that the plug can be accessed and disconnected easily in case of emergencies. WATER SUPPLY CONNECTION Before making the water supply connection, allow a quantity of water to flow from the top. The water should be clean and free from impurities, especially where the system is new or has been left unused for a length of time. There are two hoses provided with the machine. The hot water hose is indicated with a red strip running the length of the hose. Insert the filter/washer supplied (Fig. 5) before connecting the water inlet hose to the valve. Check that the other end of the hose is tight (Fig. 5A). Turn the supply valve on (Fig. 5B). The drain outlet should be positioned at a height of between 23” (60 cm) and 35” (90 cm) above the floor (Fig. 6). NOTE: To prevent siphoning, do not seal the drain hose connection into the drain outlet. If the machine is not connected to a drain outlet, place the drain hose and bracket supplied over the edge of a sink or wash basin and anchor it in place. FIG. 5 FIG. 5A Cold Hot close open FIG. 5B FIG.6 23.5" (60 mm) minimum 35" (90 mm) maximum INSTRUCTIONS FOR USING THE WASHER 1. Before placing the items in the washer, sort the laundry by type of fabric and care label instructions (see page 8). 2. Make sure nothing is in the garment pockets to avoid damage to clothes, the machine or the filter. 3. Close zippers and hooks to prevent snagging. 4. Open the door (Fig. 8). 5. Load the laundry and close the door securely. 6. Pour detergent and fabric softener into the appropriate compartments in the detergent drawer (Fig. 9). Use only low sudsing detergent made for front- loading washers and follow label instructions. The amount of detergent varies among the different brands, but for most detergents, you need only one or two tablespoons. Too much detergent could leave a residue on your clothes and possibly damage the washer. NOTE: When using a liquid detergent, insert the special container supplied with the washer into the main wash compartment (Fig 9a). Pour the manufacturer’s recommended dosage of liquid detergent into the container (Fig 9b). NOTE: Do not add detergent to the prewash compartment unless you are using a wash program that has a prewash cycle; otherwise, the machine could oversuds and spill onto the floor. Also, do not use liquid detergent for a prewash program because the detergent will be washed out the back of the drawer. NOTE: It is not recommended that you use bleach in your Eurotech washer. If you need extra whitening, we recommend that you use a low-sudsing powder detergent with bleach additive. NOTE: Excessive use of fabric softener can damage garments. 7. Close the detergent drawer securely (Fig 9c). Caution! To avoid water spillage, do not open the detergent drawer while the machine is operating. 8. Select program options (see pages 9 and 10). 9. Turn the Temperature knob to the desired temperature (see pages 9 and 10). 10. Set the Program knob to the desired program (see pages 9 and 10). 11. Press the On button (see page 9). (...
Эта инструкция также подходит к моделям:Стиральные машины - EWF150 (223.01 kb)