Оценок - 1, средний балл: 4
(
)
)
|
Фрагмент инструкции
The total time of both programs together is not displayed. The right display alternately shows the program in operation (during a longer time span) and the second program to be executed (during the shorter time span). After the fi rst program has been run, only the second program number will be displayed. Cool down This function allows to gradually lower the temperature of the wash bath to prevent creasing of the linen. During a cool down, the remaining program time on the central display will be replaced by “cd”. Power Failure Should the power fall out during the program, the water will be drained and the door can be opened after maximum 3 minutes. When the door remains locked, and the power comes back up within 24 hours, the program will continue from there, where it was at the time of the power failure. If due to breakdown, the door is not unlocked automatically, you have to remove the service panel (A) below and pull the ring (B), suspended on the left side, while opening the door. Before opening the door, check that all the water has been drained from the tub and that the cylinder has come to a complete stop. Important: Remote stop function By means of this function, no cycles can be selected anymore during a certain period of time (e.g. between 10 p.m. and 7 a.m.). This time is determined by an extern timer. As soon as the last cycle is fi nished, “ OFF “ (blinking) appears on the left display as long as this function is activated. 21 4 Machine with coin or token operation Opening the door Open the door. Fill the drum Sort the linen according to the type and required temperature of the linen. Empty all pockets of the garments so that no garments can be damaged and no left articles can cause damage to the machine. Turn sleeves of shirts, blouses inside out. It is recommended to mix small and large items to enhance the drop of the linen during the wash cycle and hence improve the wash quality. Wash loads of below 80% of machine capacity can obstruct the proper functioning of the machine and can damage the machine. Overloading the machine can also lead to a bad wash result. On machines with a coin or token meter, the programmer can contain up to 20 programs (0-19). The program number is displayed on the right display. By pressing the SELECT-button (P), the next program will be displayed. The price will be displayed on the left display. The display will count down every time a coin is introduced into the coin meter. When the total price has been introduced into the machine, the display will be switched off and the machine will start. During the fi rst 2 minutes after starting, the program number is blinking and you can change the program in case of a possibly wrong selection. To do so, select another program with the SELECT button (P). The new program will be started immediately. If a more expensive program has been selected, the price difference with the previous program will be displayed. The new program will only start after this price difference has been introduced. If this has not been done within two minutes of selecting the new program, the machine will switch back to the original program and continue operating. Close the door Select program It is recommended to only use detergents with a “foam-breaker”. These are often found in the launderette or laundry or can easily be found in retail stores. Recommended doses are mentioned on the detergent packing. Overdosing of detergents can lead to reduced wash results and “overfoaming” which can damage the machine. Add detergent Start the machine Left compartment A: Prewash (1st wash) Central compartment B: Main Wash (2nd wash) Right compartment C: Final Rinse (fabric softener) Bottom compartment D: Direct access to tub 22 4 Display information The left display will indicate the temperature of the wash bath - in °C or °F (on machines where this function has been selected). The central display shows the remaining time to the end of the wash cycle. For programs which are being run for the fi rst time, the machine will take a theoretical time estimate. If this time indication does not correspond to the real cycle time, the cycle time will be corrected from the second cycle onwards (Self-Teaching function of the machine). This function has to be specifi ed during preprogramming. The right display will continue to show the selected program number. If a "Level-stop" was programmed (which halts the programmer during the fi lling of the cylinder) and/or a "Heat-stop" (which stops the programmer during the heating up of the wash bath, then the respective LED’s light up in the display. Once the required water level and/or temperature have been reached, the LED is turned off and the internal programmer advances again. Wash cycle-LED’s Each program segment has a corresponding LED. Each of these 6 LED’s light up when the appropriate segment is executed. This way, the program sequence can be accurately followed. When a LED blinks, the machine is taking up water. When a L...
Эта инструкция также подходит к моделям:Стиральные машины - HF150 (1.7 mb)
Стиральные машины - HF185 (1.7 mb)