Оценок - 3, средний балл: 5
(
)
)
|
Фрагмент инструкции
8). Adjust them for depth based on the position of the base molding, and, if necessary, fasten the base to the guides (fig. 9). This is how to assemble the plinth guide (fig. 8). Fasten angle P using screw R, insert plinth guide Q into the special slot and once it is in the desired position, lock it in place using angle P and screw R. Inserting the machine into the Cabinet. - Push the machine into the opening, aligning it with the cabinets (fig. 6). - Regulate the adjustable feet to raise the machine to the appropriate height. - To adjust the position of the wooden panel in both the vertical and horizontal directions, use the C and D screws, as shown in fig. 7. Important: close the lower part of the appliance front by ensuring that the plinth rests against the floor. Fig. 8 Accessories provided for the height adjustment. The following can be found inside the polystyrene lid (fig. 10). 2 crossbars (G), 1 strip (M) the following can be found inside the appliance drum. 4 additional feet (H), 4 screws (I), 4 screws (R), 4 nuts (L), 2 plinth guides (Q) G M 1 llfT 1 Fig. 10 Adjusting the appliance height. The height of the appliance can be adjusted (from 815 mm to 835 mm), by turning the 4 feet. Should you require the appliance to be placed higher than the above height, you need to use the following accessories to raise it to up to 870 mm. the two crossbars (G); the 4 feet (H); the 4 screws (I); the 4 nuts (L) then perform the following operations ffig. 11). remove the 4 original feet, place a crossbar G at the front of the appliance, fastening it in place using screws I (screwing them in where the original feet were) then insert the new feet H. Repeat the same operation at the back of the appliance. Now adjust feet H to raise or lower the appliance from 835 mm to 870 mm. Once you have reached the desired height, lock nuts L onto crossbar G. To adjust the appliance to a height between 870 mm and 900 mm, you need to mount strip M, adjusting feet H to the required height. Insert the strip as follows. loosen the three screws N situated at the front of the Top cover of the appliance, insert strip M as shown in fig. 12, then fasten screws N. GB 7 Description of the Washer-dryer and starting a wash cycle Control panel wash cycle progress indicator lights Detergent dispenser drawer: used to dispense detergents and washing additives (see "Detergents and laundry'"). ON/OFF button. switches the Washer-dryer on and off. WASH CYCLE knob. programmes the wash cycles. During the wash cycle, the knob does not move. FUNCTION buttons with indicator light. used to select the available functions. The indicator light corresponding to the selected function will remain lit. TEMPERATURE knob. sets the temperature or the cold wash cycle (see "Personalisation'"). DRYING knob. used to set the desired drying programme (see "Personalisation'"). WASH CYCLE PROGRESS indicator lights. used to monitor the progress of the wash cycle. The illuminated indicator light shows which phase is in progress. DOOR LOCKED indicator light. indicates whether the door may be opened or not (see next page). START/PAUSE button with indicator light. starts or temporarily interrupts the wash cycles. N.B. To pause the wash cycle in progress, press this button; the corresponding indicator light will flash orange, while the indicator light for the current wash cycle phase will remain lit in a fixed manner. If the DOOR LOCKED ■w-O indicator light is switched off, the door may be opened. To start the wash cycle from the point at which it was interrupted, press this button again. 8 ■ Hotpoint Indicator lights ■h-O Door locked indicator light The indicator lights provide important information. This is what they can tell you: If this indicator light is on, the appliance door is locked to prevent it from being opened accidentally; to avoid any damage, wait for the indicator light to switch off before you open the appliance door. Wash cycle phase indicator lights Once the desired wash cycle has been selected and has begun, the indicator lights switch on one by one to indicate which phase of the cycle is currently in progress. ! If the START/PAUSE indicator light (orange) flashes rapidly at the same time as the function indicator light, this indicates a problem has occurred (see "Troubleshooting'). Wash Spin Dry End of wash cycle Rinse Note: as soon as a drying level or time period has been set, this indicator light illuminates to indicate END U that the selected wash cycle will be followed by a drying phase. Note: during the "Drain" phase, the indicator light corresponding to the "Spin" cycle phase will illuminate. Function buttons and corresponding indicator lights When a function is selected, the corresponding indicator light will illuminate. If the selected function is not compatible with the programmed wash cycle, the corresponding indicator light will flash and the function will not be activated. If a f...