Оценок - 2, средний балл: 3
(
)
)
|
Фрагмент инструкции
Hold, slide across and pull to remove. I t is impor tant the transit bolt and spacer come out intact (see pic). For safet y, replace both plastic covers over the holes lef t by removing the two bolts. Dispensing Powder Detergent To achieve the best wash results the manufacturer’s recommended amount of detergent should be measured and added to the main detergent compartment (II symbol) (max. 400ml). Dispensing Liquid Detergent We recommend the use of a detergent dosing ball, as provided by your detergent manufacturer. Alternatively you can obtain a liquid detergent flap, a barrier for the dispenser drawer. Contact Genuine Parts and Accessories (see Key Contacts) Adding Fabric Conditioner Pre-wash Programme A Pour the recommended When selecting programme A, amount of fabric add detergent to both the conditioner into the pre-wash compartment (I symbol) compartment and the main wash compartment (flower symbol). (II symbol). Do not exceed the DO NOT use in drum dosing maximum fill line. devices with the Pre-wash programme, A. Index: 1. Drawer release latch 2. Pre-wash detergent compar tment Maximum 200ml powder or 100ml liquid 3. Main detergent compar tment Maximum 400ml powder or 200ml liquid 4. Grate 5. Fabric conditioner compar tment 120ml maximum 1 2 3 4 5 WARNING: Do not put any items into the drawer, other than detergents designed to be released from the drawer, as they may cause damage or block age. 3 CONNECT TO THE WATER SUPPLY... iii 4 DR AINAGE SYSTEM... we recommend one of the following: NOTE: ALTHOUGH YOU MAY NEED TO MOVE THE HOOKED END SUPPORT ALONG THE GREY DR AINAGE HOSE, DO NOT REMOVE IT. WHICHEVER DRAINAGE METHOD YOU USE, MAKE SURE THAT THE HOOKED END SUPPORT IS FIXED LEVEL TO, OR ABOVE THE ‘PLUMBING INDIC ATOR LINE’* (*see G etting to Know your Appliance) PLEASE USE THE NE W HOSES SUPPLIED, FIT TED TO THE MACHINE. I f you have no hot water supply... Old hoses may cause leaks due to worn out washers. Check both hot and cold water supplies are running freely... A cold fill adaptor is available fromyour local authorised S er vice Centre or by calling the G enuinePar ts & Accessories Hotline (seeKey Contac ts). Connec t fill hoses to water supply taps: Red or Grey Hose end to Hot and Blue Hose end to Cold. TURN BOTH TAPS ON... 2 REMOVE T WO TR ANSIT FIXINGS... Follow these instruc tions to remove the T WO transit fixings. IMPORTANT: Situated, one either side of the rear panel, both transit bolts (complete with spacers) MUST be removed before use... Failure to do so may cause damage to your machine! DO NOT REMOVE! STANDP IPE METHOD UNDER SINK METHOD OR Attach the GREY drainage hose to the under sink drainage unit securely, using a hose clip. Fix the hook ed end suppor t at a minimum 800mm from the floor. cut off the blocked end of the under sink drainage unit. ............................. Standpipe height: minimum 500mm from the floor. Inser t drainage hose approximately 100mm into the standpipe. Use a crosshead screwdr iver to remove the plastic cover. 800mm from floor Hooked End Suppor t WARNING: The appliance must be earthed. POLYSTYRENE BLOCK... Fuses Your appliance comes fitted with a plug and a 13 amp (13A) fuse.If you need to replace the fuse, use only those rated at 13 amp (13A) and ASTA approved to BS1362. To change the fuse lift the holder to vertical position and lift the fuse out. To replace the fuse, insert the fuse and push fuse holder down into the locked position. Correct replacement is identified by colour coding or the marking on base of plug. WARNING: Do not use the plug unless the fuse holder is in the locked position and the top cover firmly replaced. This is part of the packaging and If you have damaged the existing lead and need a new one, contact Changing the Mains Lead should have come away with the Creda Service UK on: 08709 066 066 or polystyrene base. (or in the Republic of Ireland on: 1850 302 200). A charge will be made. We strongly advised that fitting a new lead is carried out by a IF IT HAS NOT... REMOVE IT! qualified electrician. Seek professional advice if you need to use an extension lead. NOTE: YOU MAY NEED A SECOND PERSON TO HELP YOU RAISE AND LOWER THE APPLIANCE. Changing the Plug 1 If you need to change your plug, if it does not fit your socket: isolate the machine from the mains supply. Cut off the supplied plug and safely dispose of the discarded plug. DO NOT plug into any other socket. NOTE: If you change the plug, the colour of wires in the mains lead may not match the colour of the markings which show the different terminals in the plug. You must wire it as shown below: Green and yellow (Earth) wire to terminal marked ‘E’, symbol , or coloured 13A ASTA approved fuse to green and yellow. BS1362. Brown (Live) wire to terminal Blue (Neutral) wire to marked ‘L’ or coloured red. terminal marked ‘N’ or coloured black. 5 LEVEL?... YOUR MACHINE WILL BE NOISY IF THE T WO FR ONT FEET ARE NOT ADJUSTED SO THE MACHINE STANDS FIRM AND LE VE...