Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Important! • The “Delay start” cannot be used with “Drain” or “Spin” programmes. Note! • With programme “Soak 30°” the selected delay (up to a maximum of 10 hours) corresponds to the soak time of the laundry in the drum. • The door will be locked throughout the delay time. If you need to open the door, you must first set the washing machine to Pause by pressing the “Start/Pause” button. After you have closed the door, press the “Start/Pause” button again. 16 9 “Start/Pause” button This button has two functions: • Start: after you have selected the desired programme and options, press this button to start the washing machine. The light above the button will stop flashing and remain lit. If you have selected a delay time, the countdown will begin and will be shown on the display. • Pause: when you press this button again, the programme in progress is interrupted. The light above the button will start flashing. To restart the programme from the point at which it was interrupted, press the button again. Important! You must set the washing machine to Pause before you make any change in the programme in progress. 10 Display (Programme time) The following pieces of information are shown on the display: • Reset/cancellation of the programme If the programme selector dial is turned to “Off” position, three blinking dashes are displayed. Now you can select a new programme. (If, at the end of a washing cycle, the programme selector dial has not been turned to “Off” position , when you press the “On/Off” button to switch the machine on for the next washing, the display will show a blinking zero.) • Duration of washing programme in hours and minutes, after you have selected a programme (for example 2.05). The duration is calculated automatically on the basis of the maximum recommended load for each type of fabric. While the programme is running (after you have pressed the Start/Pause button), the displayed time value decreases by one unit every minute. • The washing machine has stopped with water in the tub, when the “Rinse hold” or“Quiet” option has been selected or at the end of the “Soak 30°”: this is indicated by a flashing zero. • The washing machine has completed the programme: this is indicated by a flashing zero. • Delay start, a time value indicated in hours (23 hours max) and selected by means of the relevant button. 17 The delay time is displayed for 3 seconds, then the duration of the selected programme reappears. After you have pressed the Start/Pause button, the countdown is updated every hour, and, for the last two hours, every 30 minutes. • An incorrect option selection has been made: this is indicated by the message Err when a function incompatible with the current programme is selected. • An alarm code indicates a fault in the machine operation (see page 29, "Something Not Working"). The “End” pilot light flashes in the event of operating problems. And the relative alarm code appears on the display. E EE1 110 00 = the machine does not fill E EE2 220 00 = the machine does not empty E EE4 440 00 = the door has not been closed To eliminate the problem, see paragraph “Something not working” (pages 29-30). Important! If you turn the programme selector dial to another programme when the machine is working, all the lights of the programme progress display will flash for about 2 seconds but the machine will not perform the new selected programme. 12 Programme selector dial The programme selector dial is divided into the following sections: • Cottons, • Synthetics, • Delicates • Wool / Hand washing • Special programmes from “Soak 30°” to “30 Minute wash” • Reset programme “Off” 11 Programme phase indicator lights When you select a programme, the lights relevant to the phases that form the programme light up. After you have started the programme, only the light relevant to the phase that is currently being carried out will remain lit. When the washing programme has finished, the “End” light comes on and a flashing zero appears on the display. The light of the “Start/Pause” is off. - .#/'#/ .#/ .#/.#, '#/"%/ !0#/ !'#/0#/'#/.#/0#/'#/ !'#/ '#/- - - The selector dial can be turned either clockwise or anticlockwise to select the required wash programme . “Economy” position corresponds to an ENERGY SAVING programme and “Cold” to a cold wash. Before setting the dial to any position ensure that the machine is turned to the “Off” position. Important! At the end of the programme the selector dial must be turned to position “Off”. 18 Programme information Easy iron 40° With this programme at 40°C it is possible to wash synthetic garments which must be ironed. The laundry is gently washed and spun to prevent the fabrics from creasing. Max. load 1 kg. Final spin speed 900 r.p.m. Soak 30° This is a special programme for heavily soiled laundry. The machine performs a soak of about 20 minutes at 30°C. At the end of the soak time the machine will stop automatically with water left in the tub. T...