Оценок - 3, средний балл: 4.7
(
)
)
|
Фрагмент инструкции
This will shut off the water supply to the washer and prevent the unlikely possibility of damage from escaping water. Leave the door open to allow the inside of the washer to dry out. Use a soft cloth to wipe up all detergent, bleach or other spills as they occur. Clean the following as recommended: Control Panel – Clean with a soft, damp cloth. CLEANING THE INTERIOR Clean the interior of the washer periodically to remove any dirt, soil, odor, mold, mildew or bacteria residue that may remain in the washer as a result of washing clothes. We recommend taking the following steps every 60 to 120 days to clean and freshen your washer interior. The frequency with which the washer should be cleaned and freshened depends on factors such as usage, the amount of dirt, soil or bacteria being run through your washer or the use of cold water. Failure to follow these instructions may result in unsatisfactory conditions, including unpleasant odor and/or permanent stains on the washer or washload. CLEANING THE DISPENSER The dispenser may need to be cleaned periodically due to laundry additive build-up. For easy cleanup of the dispenser, grasp the removable two-compartment container (for bleach and softener) as shown in illustration #1. As you begin to lift the two-compartment container, tilt slightly inward, according to illustration #2 and remove from the main dispenser. Once the two-compartment container is removed from the main dispenser, take it to a sink. Follow illustration #3 to Do not use abrasive powders or cleaning pads. Do not spray cleaners directly on the panel. Cabinet – Clean with soap and water. Antimicrobial Product Protection This washer is equipped with antimicrobial component protection. The rubber door seal is treated to be resistant to mold, mildew and odor-causing bacteria. To clean and freshen the washer interior: 1. Make a solution of one cup chlorine bleach and two cups warm water. Be careful not to spill or splash the bleach solution. 2. Wipe the lower portion of gray door seal with bleach solution and soft cloth. 3. Fill the bleach dispenser with chlorine bleach. 4. Run the washer through a complete cycle using hot water. 5. Repeat the wash cycle if necessary. Hard water deposits may be removed, if needed, using a recommended cleaner labeled “clothes washer safe.” remove the cap covering the siphon tube for the bleach and softener. Run warm water and a soft brush or cloth over the two parts to remove any excess laundry additives. Clean the main dispenser area using water and a soft cloth. Once the main dispenser is clean, follow the illustrations in reverse order to replace the two compartment container to its original location. NOTE: Do not use any cleaning substance but water in the main dispenser. It is possible for cleaning substances to drain into the tub. If this should happen, set the washer for a rinse and spin cycle to remove any cleaning substance from the washer before doing a load of laundry. MAX FILL MAX FILLBLEACH SOFTENER 1 2 3 8 STORING THE WASHER Washers can be damaged if water is not removed from hoses and internal components before storage. Prepare the washer for storage as follows: • Select the COTTON/STURDY and QUICK WASH settings and add one cup of bleach to the detergent dispenser without clothes in the tumbler. Run the washer through a complete cycle using hot water. • Turn the water faucets off and disconnect the inlet hoses. • Disconnect the washer from the electrical supply and leave the washer door open to let air circulate inside the tumbler. • If the washer has been stored in below-freezing temperatures, allow time for any water left over in the washer to thaw out prior to use. For information on long-term storage or storage of your washer during extreme cold temperatures, call Maytag Services, LLC toll-free at 1-800-688-9900 USA. U.S. customers using TTY for deaf, hearing impaired or speech impaired, call 1-800-688-2080. REVERSE THE DOOR Washer door swing direction can be changed using the following procedure: 1) Swing door fully open and support it while removing four hinge screws (which hold hinges to door assembly). 2) Move the door to a work surface and transfer four door screws to the opposite side of the door assembly. 3) Remove one screw holding top hinge to cabinet and one screw holding top hinge cover to cabinet (opposite side). 4) Remove hinge and bracket from cabinet by moving them up and down to a position where they are released. 5) Install hinge and bracket in swapped locations and drive screws to attach them securely to the cabinet. 6) Compare top hinge and top bracket to bottom hinge and bottom bracket for correct hinge assembly position. 7) Repeat procedures 4 through 6 for bottom hinge to cabinet and bottom bracket to cabinet. 8) Support door in fully open position on hinge side and drive four screws to securely attach hinges to door assembly. 9) Close door and check to see that washer operates properly. 9 TROUBLESHOOTING CHECK THESE POINTS IF YOU...