Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
23 Unpacking All transit bolts and packing must be removed before using the appliance You are advised to keep all the packaging for re-use in case the appliance has to be transported again. ¦ Unscrew and remove the three rear transit bolts (using a spanner). ¦ Lay the machine gently on its back, making sure that the hoses are not squashed. We suggest a polystyrene angle bracket from the packing is placed on the floor before tilting it back to avoid the hoses being squashed. ¦ Carefully remove the polyethylene bags located at the base of the machine by pulling them toward the centre of the machine. ¦ Place the machine in an upright position and remove the three plastic bolts. ¦ Plug the 3 holes with the plastic plugs which you can find in the envelope containing the instruction booklet. P0287 P0018 1 2 AL009 P0001 P0002 24 Positioning Your new Electrolux washing machine has been designed to be permanently plumbed in to your home’s water supply and drainage system. However, if this is not possible, it may be connected to suitable existing taps, with the drain hose discharging into the sink. The appliance has two inlet hoses, hot and cold, with female 3/4” BSP thread connectors. If this connection is not compatible with the plumbing of the existing installation, a variety of connectors are available from good hardware stores and plumbers merchants to suit most domestic plumbing. Any alterations to your existing plumbing must be carried out by a competent person, or qualified plumber. Water inlet The inlets on the back of the appliance are colour coded, blue for cold and red for hot. Before connecting the hoses, be sure to fit the black washers supplied as per diagram. If only a cold water supply is available, connect the two hoses to a cold water outlet by means of a ‘Y’ connection piece. Installation should comply with local water authority and building regulation requirements. The appliance must be given a separate cold water supply and not be connected to a mixer tap, a single outlet water heater or a booster pump. A minimum water pressure of 7psi is required for safe operation of the appliance. If you cannot make the cold water connection direct from the rising mains, you may be able to operate the appliance from your cold water storage system. There should be a minimum distance of 5.02m (16 1/2ft) between the appliance’s inlet and the bottom of the tank. There will be sufficient pressure for the hot water supply from the hot water cylinder if the height between the appliance’s inlet and the bottom of the cold water storage cistern (not between the appliance and the hot water cylinder) is at least 2.74m (9ft). Set the hoses correctly by loosening the ring nuts. After positioning the inlet hoses, be sure to tighten the ring nuts again to prevent leaks. COLD WATER SUPPLY HOT WATER SUPPLY AL013 A P0021 25 Water drainage This appliance is designed to be permanently plumbed into your home's water supply and drainage system. The appliance drain hose should hook (use the plastic “U-piece” supplied) into a standpipe with an internal diameter of approximately 38mm (see diagram) thus ensuring there is an air break between the drain hose and standpipe. When discharging into a standpipe ensure that the top of P1039 3 pin Max. 90 cm.(35.4") Min.60 cm.(23.6") the curve in the hose end is no more than 90cm (35.4'') Min. 30 cm.(12")38 mm.(1/ ") diameter standpipe 1 2 and no less than 60cm (23.6'') above floor level. The upright standpipe should have a minimum length of 30cm (12'') from the bottom of the elbow to the top of the pipe (see diagram). P1040 Make sure that it is designed in such a way, that the end of the drain hose cannot be covered with water. The drain hose may be extended to a maximum of 3 metres. An additional drain hose and joining piece is available from your local Service Force Centre. The joining piece must have an internal diameter of 18mm. If you intend the drain hose to empty into a sink, make sure that the sink is empty and the plug hose is not blocked. Use the plastic “U-piece” supplied. P0022 26 Levelling Level the washing machine by loosening or tightening the feet. Once in the right position fix the feet by pushing the nuts against the base of the case. Accurate levelling prevents vibration, noise and displacement of the machine during operation. After levelling the machine, secure the feet by tightening the ring nuts with the aid of a screwdriver. Some vibration is inevitable, especially if mounted on a wooden floor. Sprung wooden floors are particularly susceptible to vibration. For advice, consult a builder. If possible, always place the machine on a solid floor. Special conditions If the floor is carpeted with a deep-pile carpet or covered with crumbly or soft material, insert a rigid support base under the feet to prevent noise, vibration or displacement. The base should protrude a few centimetres beyond the edges of the machine. P0254 P0509 Warning The machine should NOT be placed on deep...