Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
---Flashes for a period of time (for safety) after power up while keeping outputs OFF Adv Machine set up for Rapid Advance noAd Machine is not set up for Radid Advance Erdn Drain count error (depending on model) Erfl Fill error count (depending on model) E Pr The number of times power has been interrupted during a cycle (will display in certain models) CyC Cycle counter © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F232219 Operation Operating Instructions 5. Close door and turn handle counterclockwise until button pops out. Refer to Figure 6. 1. Turn on main power source (circuit breaker) with right hand. 2. With left hand, push and hold white rocker button. Refer to Figure 4. 3. Push button and turn handle clockwise to open. Refer to Figure 4. U005I Figure 6 6. The default wash cycle will display. NOTE: Perm Press Hot is the default cycle if none is selected. CHM2027N Figure 4 4. Load to capacity whenever possible. DO NOT OVERLOAD. Refer to Figure 5. NOTE: Underloading can cause out-of-balance conditions that can shorten machine life. U003I Figure 5 Figure 7 CHM522N CHM1764C WASH ADD BLEACH RINSE SPIN DOOR CLEAN FILTER NORMAL LIGHT SOIL UNIFORMSHEAVY SOIL STAINED DELICATE HOT HOT HOT HOT HOT HOT WARM COLD START PERM PRESS VISA TM DOMESTIC MODELS 60C 60C 40C 40C 95C 95C << 30C INTERNATIONAL MODELS F232219 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Operation 7. If desired, select a different cycle at this point. The LED indicator for that cycle will light. 8. Add liquid and/or powder supplies to supply dispenser. Refer to Figure 8. a. Add detergent to compartment 1. b. Add softener to compartment 3. 1 2 CHM486R 1 Detergent 2 Bleach 3 Softener Figure 8 9. When applicable, add bleach to compartment 2 when the ADD BLEACH LED is lit. 10. Press the desired wash cycle keypad if none is selected. 11. Press the START keypad. 12. During first fill, the desired wash cycle can be changed. After first fill has ended, the wash cycle active at that moment remains the chosen wash cycle. 13. When cycle is complete, display shows “donE”. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F232219 Maintenance Sharp edges can cause personal injury. Wear safety glasses and gloves, use proper tools and provide lighting when handling sheet metal parts. W366R1 WARNING IMPORTANT: Replace all panels that are removed to perform service and maintenance procedures. Do not operate the machine with missing guards or with broken or missing parts. Do not bypass any safety devices. Daily IMPORTANT: Door lock should be checked daily to ensure proper operation. Also check that all safety and instruction stickers are on the machine. Any missing or illegible safety instructions stickers should be replaced immediately. Beginning of Day 1. Inspect water inlet valve hose connections on the back of the machine for leaks. 2. Inspect steam hose connections for leaks (where applicable). 3. Verify that insulation is intact on all external wires and that all connections are secure. If exposed wire is evident, call a service technician. 4. Check door interlock before starting operation: a. Attempt to start the machine with the door open. The machine should not start with the door open. b. Close the door without locking it and attempt to start the machine. The machine should not start with the door unlocked. c. Close and lock the door, and start a cycle. Attempt to open the door while the cycle is in progress. The door should not open. If the door lock and interlock are not functioning properly, call a service technician. End of Day 1. Clean the door gasket of residual detergent and all foreign matter. 2. Clean automatic supply dispenser lid and general area. Flush dispenser with clean water. 3. Clean the machine’s top, front and side panels with mild detergent. Rinse with clean water. 4. Leave loading door open at the end of each day to allow moisture to evaporate. NOTE: Unload the machine promptly after each completed cycle to prevent moisture buildup. Leave loading door open after each completed cycle to allow moisture to evaporate. F232219 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Maintenance Weekly 1. For variable-speed models only, clean the AC drive box filter(s) weekly or more frequently as needed: NOTE: If fan filter service indicator light is on, fan filter must be cleaned immediately to prevent possible damage. Thermostat automatically resets after drive compartment cools down. LED will then extinguish after cycle run. IMPORTANT: If filter indicator is ignored, repeated resets might shorten life of drive. Clean filter regularly to avoid indicator prompt. a. Open the top cover. b. Grasp the filter handle and pull straight up to remove filter. c. Wash the filter with warm water and allow filter to air-dry. As an alternative, the filter may be vacuumed clean. IMPORTANT: The control module cover and fan filter must be in place for the fan to properly cool the A...