Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
-8 For Machines Mfg. Since 7/09 PREP A R A T I O N EVS Toolroom Lathes Inventory Main Inventory 1: (Figure 2) Qty A. Steady Rest Assembly ....................................1 B. 12" Faceplate w/D1-6 Camlock Stud Set ......1 C. 10" Four-Jaw Chuck w/Combo Jaws .............1 D. Four-Jaw Chuck Key .....................................1 E. Four-Jaw Chuck D1-6 Camlock Stud Set .....1 F. Follow Rest Assembly ....................................1 Tool Box Inventory: (Figure 3) Qty G. Tool Box ..........................................................1 H. Three-Jaw Chuck Key ...................................1 I. Tool Post T-Wrench ........................................1 J. Hex Wrench Set 1.5-10mm ............................1 K. Dead Center MT#4 .........................................1 L. Carbide-Tipped Dead Center MT#4 ..............1 M. Tapered Spindle Sleeve MT#6-#4 .................1 N. Open End Wrench 22/24mm .........................1 O. Open End Wrench 14/17mm .........................1 P. Open End Wrench 10/12mm .........................1 Q. Phillips Screwdriver #2 .................................1 R. Standard Screwdriver #2 ...............................1 S. 9"-Chuck Jaws (SB1014-15, SB1037-38) ......3 8"-Chuck Jaws (SB1012-13) ..........................3 T. Cast Iron Leveling Pads ................................8 U. Handwheel Handles .......................................2 Note: Some inventory components may be shipped inside of the lathe electrical box. These items MUST be removed before connecting the lathe to the power source. A B CD E F Figure 2. Main inventory. G H I J K L M N O P Q R S T U Figure 3. Toolbox inventory. -9 EVS Toolroom Lathes PREP A R A T I O N For Machines Mfg. Since 7/09 Cleaning & Protecting The unpainted surfaces are coated at the factory with a heavy-duty rust preventative that prevents corrosion during shipment and storage. The benefit of this rust preventative is that it works very well. The downside is that it can be time-consuming to thoroughly remove. Be patient and do a careful job when cleaning and removing the rust preventative. The time you spend doing this will reward you with smooth-sliding parts and a better appreciation for the proper care of the unpainted surfaces. Although there are many ways to successfully remove the rust preventative, we have cleaned thousands of machines and found the following process to be the best balance between efficiency and minimized exposure to toxic fumes or chemicals. Before cleaning, gather the following: ... ......................rags ... .................................. (certain citrus-based degreasers work extremely well and they have non-toxic fumes) ... ..................................................................S Note: Automotive degreasers, mineral spirits, or ............................................................................................. Before using these products, though, test them on an inconspicuous area of a painted area to make sure they will not damage it. GAS Gasoline and petroleum products have low flash points and can explode or cause fire if used for cleaning. Avoid using these products to remove rust preventative. Many cleaning solvents are toxic if inhaled. Minimize your risk by only using these products in a well ventilated area. Avoid chlorine-based solvents, such as acetone or brake parts cleaner that may damage painted surfaces. Always follow the manufacturer’s instructions when using any type of cleaning product. Basic steps for removing rust preventative: 1. Put on safety glasses and disposable gloves. 2.. ........................................................................................... with a liberal amount of your cleaner or degreaser and let them soak for a few minutes. 3. Wipe off the surfaces. If your cleaner or degreaser is effective, the rust preventative will wipe off easily. Note: To clean off thick coats of rust preventative on flat surfaces, such as beds or tables, use ................................................................................... majority of the coating before wiping it off ........................................................................................... it may scratch the surface.) 4. Repeat Steps 2–3 as necessary until clean, then coat all unpainted surfaces with a quality metal protectant or light oil to prevent rust. -10 For Machines Mfg. Since 7/09 PREP A R A T I O N EVS Toolroom Lathes Location Physical Environment The physical environment where your machine is operated is important for safe operation and longevity of parts. For best results, operate this machine in a dry environment that is free from excessive moisture, hazardous or flammable chemicals, airborne abrasives, or extreme conditions. Extreme conditions for this type of machinery are generally those where the ambient temperature is outside the range of 41°– 104°F; the relative humidity is outside the range of 20–95% (non-condensing); or the environment is...
Эта инструкция также подходит к моделям:Станки - SB1012 (6.59 mb)
Станки - SB1037 (6.59 mb)
Станки - SB1038 (6.59 mb)
Станки - SB1013 (6.59 mb)