Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
The information you need to enter in this menu should be supplied by your broadcaster or local aerial installer. Channel: Select the channel you want to search for. Network search: Select “Yes” if you want to search on all transmitters connected to a specific network. • Press select to start searching for channels. • Within this menu you can also check the strength of your digital signal if you know the UHF channel numbers for your area (This information can be supplied by your local aerial installer.) Alternatively if you exit this menu and go to a selected channel then re-enter this menu you will see the signal strength for that chosen channel. Advanced manual search The information you need to enter in this menu should be sup plied by your broadcaster or local aerial installer. You can use this menu if you are looking for some “specific” channels (i.e. non-DVB standard channels) which can be more easy to find when you have entered the necessary PID settings here. Channel: Select the channel you want to search for. PID Video: Enter the PID (Packet Identifier) for the video signal. PID Audio: Enter the PID for the audio signal. PID PCR: Enter the PID for the PCR (Programme Clock Refer ence). • Press select to tune with the specified values. All channels created with advanced manual search will get an automatically generated name, e.g. P0001 for the first channel, P0002 for the second etc. • Press select to save the new channel or back if you do not want to save it. GB 19 Navi Bars Navi Bars Settings folder . TV To open this menu you will be asked to enter your access code. From the factory the access code is set to 1234. From here you can adjust the audio/video settings for your Media- master. TV screen format Select your TV screen format. The 4:3 format is the standard format for most TV screens. Select 16:9 for a widescreen TV. Position of the RGB output Adjust the horizontal position of the TV picture with the buttons. Set transparency level Adjust the transparency level of the graphics in the menus by using the buttons. Select digital audio format Select audio format for the digital output. (The upper audio output on the rear of the Mediamaster). AC-3 when the sound is transmitted in Dolby™ Digital format. PCM for ordinary digital sound. Please note; When you select AC-3 there will be no sound output from the analogue audio connections. Picture format If you have a TV set with the 4:3 picture format and the transmission is in 16:9, you can select “Fullscreen” or “Letterbox”. If you have the stretched and boxed format 14:9, you select “Combined”. Fullscreen will fill up the screen but will cut off some information fullscreen letterbox on the left and right sides. Letterbox will give a complete picture, but leave black areas at the top and bottom. Combined will give black areas both at the top and bottom and also on both sides RF modulator output channel Select this alternative if you have to change the RF channel. (Channel 43 is preset from factory.) When you change the RF channel number, you must also change to the same value on the TV. If you do not, there will be no picture and sound. GB 20 Navi Bars Navi Bars Settings folder . Modem General In the future some Service Providers may make it possible for you to order e. g. movies via an external phone modem. Normally you do not need to change any of the following settings. They are there to make it possible to use any external modem that accepts AT commands. For more information about AT commands, please consult the documentation of your particular modem. Prefix If the connection has to pass a switch board, enter the digit(s) that will open the line. International dialling code This sequence of numbers will replace the ‘+’ sign in an international phone number where the ‘+’ sign is followed with country code, area code and actual local number. Maximum length of the number is four digits. Modem initialising In most cases you can leave this field empty. To start with, always check your system without entering anything in this field. Baudrate This field specifies the data transfer rate (speed) between your Mediamaster and your modem. In most cases modems can detect the right speed automatically. Default value is 57600 bits/s. If your modem does not seem to respond, enter a lower value. GB 21 Navi Bars Navi Bars Settings folder . Access Ctrl To open this menu you will be asked to enter your access code. From the factory the access code is set to 1234. The following settings can be altered from this menu. Access Control Select “Yes” or “No” to turn the access control in all menus on or off. Note: Even when “No” is selected, the access code still has to be entered before you can watch locked channels. Receiver lock If you select “Yes” you will have to enter the access code every time you start the Mediamaster from standby. Age rating control If you want everybody to have access to all available types of pro grammes, select “No” If you select “Yes” you may bl...