Войти:
Оценок - 3, средний балл: 3.7 ( )

Инструкция по эксплуатации Kathrein, модель Twin-PVR Satellite UFS 821sw

Производитель: Kathrein
Размер: 5.76 mb
Название файла:
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


Audio Settings Setting the Volume Set the required volume level using the . buttons on the remote control of the receiver. A bar indicator is displayed on the screen to show the set volume. Muting Press . to mute the sound. “Sound off” is displayed. Press the button again to restore the sound. Stereo and Two-Channel Sound Playback Use the yellow . button to open the Audio menu for sound and language selection, where you can make the desired settings, e.g. subtitles, language selection (soundtrack), audio mode, digital output (MPEG stereo, AC 3), as long as they are included in the reception signal: Select the menu options using the .. buttons and make the desired setting using the .. buttons. Press the yellow . button again to exit the menu. Possible audio settings include: - Audio Track: 1st option = Auto (oriented to menu setting) 2nd option = Audio tracks 1 -X (of the tracks transmitted by the channel) - Audio Channel: Choose between menu setting, Stereo, Mono left and Mono right -Subtitle: Enable/disable AC 3 The receiver has an optical audio output for AC3 format (Dolby Digital). This gives you the opportunity to bring cinema quality sound into your living room. The AC 3 sound is recorded and can be selected during playback. Connect the corresponding digital audio output to a Dolby Digital system. If no AC3 signal is received, you can only make the normal stereo or Always follow the operating mono settings, and choose the broadcast languages. instructions for your Dolby Digital system. Recording The UFS 821 offers you the following options for recording a programme: - Time-shift Allowing you to include the background recordings made up to that point to be included in your recording - Record direct to hard disk Allowing you to start recording immediately or later - Timer recording (see tvtv EPG) Allowing you to coordinate your recordings and plan them well ahead, also providing a range of options such as the series timer Check that there is adequate hard disk capacity available before every recording! You can see this on the right-hand side of the “Recording List” menu, indicated as “Disk Usage”. It is impossible to say exactly how much storage space a recording will take up, as this depends on the volume of data content transmitted. You can work on a basis of about 1.5 GB for one hour’s recording. Recording Direct to Hard Disk (Store Time-Shift Recording) The UFS 821 offers you a special feature in this context. As soon as you switch to a channel, the receiver automatically starts recording the programme you are viewing to the hard disk in the background. When you change channel again, the stored data is deleted and background recording begins again. If, after viewing the programme for a time, you decide you want to record it, you can do so as from the point you switched to the channel in question. Precondition: On the “PVR Setup” menu the “Automatic time-shift” option must be set to “On” and the “Time-Shift Buffer Size” entry must allow sufficient hard disk capacity for the time-shift recording. Also refer to the “User Preference” section on this, under “PVR Setup”. Recording Start Press the red . button. The following display appears: When recording starts, only the data of the current programme is recorded. The programme running before you switched channels is not recorded. If there is an overlap with another scheduled or ongoing recording, the fact is indicated. The receiver then presets the end time for your new recording as the start time of the overlapping programme (see “Duration/ End” at the right). You can start recording the programme as from the point you switched to the channel in question simply by pressing the . button, or you can simply wait the 5 seconds for automatic recording to begin. If you want to alter the end time or recording duration, you can do so as described under “Duration/End” before pressing . to start recording. Duration/End You can specify the duration of a recording regardless of when it starts. The receiver automatically retrieves the end time of the programme you are currently viewing from the EPG data (where available) and inserts it in the “Duration” field. Otherwise the end time is based on the default duration you set on the “User Preference” menu under “PVR Setup”. If your programmed recording overlaps with another scheduled recording, the end time of the current recording is matched to the start time of the one already scheduled. To change the recording duration, use the .. buttons to move to the “Duration” field and use the .. buttons to select the time after which you want recording to stop automatically. Press . to shorten the recording by 10 minutes and . to extend it by 10 minutes. When you have finished making your settings, use the .. buttons to select “OK” and press . to start recording. If the end time still overlaps with the start time of a scheduled recording, the receiver automatically switches to the tvtv-EPG's timer list, where you can delete, ca...

Эта инструкция также подходит к моделям:
Спутниковые ресиверы - Twin-PVR Satellite UFS 821si (5.76 mb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории