Оценок - 3, средний балл: 3.7 ( )

Производитель: Sirius Satellite Radio Размер: 1.77 mb Название файла: Язык инструкции:

Trim off the excess cable tie. Route the remainder of the antenna cable to where you are locating the Combiner. When routing the antenna cable, be careful not to pinch, squash, kink, or crimp the cable, or cut, damage, or puncture the external jacket of the antenna cable. Connect one of the RG-6 cables you purchased from the SIRIUS antenna to the SIRIUS RaDIo port on the Combiner (SR2261) as shown. (Refer to page 5 for the Combiner port identification.) M EXISTING RG-6 CABLE EXISTING RG-6 CABLE (NOTE: Not present if multiswitch is integrated into the satellite dish) C Combiner Step 4 Step 3 Step 5 Step 2 Multiswitch (NOTE: Multiswitch may be integrated into the satellite dish) 3. Home Signal Distribution Kit Installation Guide 4. Disconnect the cable from the multiswitch and connect it to the ComBIneD oUT port on the Combiner (SR2261) as shown. (Refer to page 5 for the Combiner port identification.) 5. Using one of the RG-6 cables which you purchased, connect it between the multiswitch and the DBS In port on the Combiner (SR2261) as shown. (Refer to page 5 for the Combiner port identification.) Step 6 Step 9 Step 8 SplitterSMCCombinerMultiswitchStep 7 Step 10 Disconnect the existing cable run from the satellite TV receiver/tuner and connect this end of the cable to the ComBIneD In port on the Splitter (SR2251) as shown. (Refer to page 5 for the Splitter port identification.) Connect another of the RG-6 cables you purchased between the satellite TV receiver/tuner and the DBS TV port on the Splitter (SR2251) as shown. (Refer to page 5 for the Splitter port identification.) Connect another of RG-6 cables you purchased between the SIRIUS oUT port on the Splitter (SR2251) and the f connector end of the supplied RG174 Adapter cable as shown. (Refer to page 5 for the Splitter port identification.) Connect the other end of the RG-174 Adapter Cable to the anT connection on your SIRIUS radio as shown. Verify that the satellite TV receiver/tuner is plugged into a working AC out6. 7. 8. 9. 10. let. Next, connect the provided AC Power Adapter to the PoWeR In port of the Splitter (SR2251), and plug it into a working AC outlet. The installation is now complete. Home Signal Distribution Kit Installation Guide after multiswitch Configuration Installation Procedure (Multiswitch Inside Home) Once the antenna has been mounted according to the previous instructions, you can continue with the installation of the Combiner and Splitter: 1. Be sure that the satellite TV receiver/tuner is plugged into an AC outlet. 2. Take the RG-6 cable which you purchased to connect to the SIRIUS antenna and thread one end of the cable through the opening in the end of the rubber boot. Then connect the cable to the antenna pod as shown in the illustration following. Slide the rubber boot over the cable connection to provide a weather proof seal and install the cable tie around the cable directly below the rubber boot to prevent the rubber boot from slipping down. Trim off the excess cable tie. Route the remainder of the antenna cable to where you are locating the Combiner. When routing the antenna cable, be careful not to pinch, squash, kink, or crimp the cable, or cut, damage, or puncture the external jacket of the antenna cable. Connect one of the RG-6 cables you purchased from the SIRIUS antenna to the SIRIUS RaDIo port on the Combiner (SR2261) as shown. (Refer to page 5 for the Combiner port identification.) M EXISTING RG-6 CABLE EXISTING RG-6 CABLE C Combiner Multiswitch Step 4 Step 3 Step 5 Step 2 3. 4 Home Signal Distribution Kit Installation Guide 4. Disconnect the cable from the multiswitch and connect it to the ComBIneD oUT port on the Combiner (SR2261) as shown. (Refer to page 5 for the Combiner port identification.) 5. Using one of the RG-6 cables which you purchased, connect it between the multiswitch and the DBS In port on the Combiner (SR2261) as shown. (Refer to page 5 for the Combiner port identification.) Step 6 Step 9 Step 8 SplitterSStep 7 Step 10 M EXISTING RG-6 CABLE C Combiner Multiswitch Disconnect the existing cable run from the satellite TV receiver/tuner and connect this end of the cable to the ComBIneD In port on the Splitter (SR2251) as shown. (Refer to page 5 for the Splitter port identification.) Connect another of the RG-6 cables you purchased between the satellite TV receiver/tuner and the DBS TV port on the Splitter (SR2251) as shown. (Refer to page 5 for the Splitter port identification.) Connect another of RG-6 cables you purchased between the SIRIUS oUT port on the Splitter (SR2251) and the f connector end of the supplied RG174 Adapter cable as shown. (Refer to page 5 for the Splitter port identification.) Connect the other end of the RG-174 Adapter Cable to the anT connection on your SIRIUS radio as shown. Verify that the satellite TV receiver/tuner is plugged into a working AC out6. 7. 8. 9. 10. let. Next, connect the provided AC Power Adapter to the PoWeR In port of the Splitter (SR2251), and plug it into a ...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: