Оценок - 3, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
Check Product Safety Upon completion of any service or repairs to this product, the service technician must perform safety checks to determine that this product is in proper operating condition. Protect the Product when Moving It Always disconnect the power source when moving the apparatus or connecting or disconnecting cables. WARNING: Avoid personal injury and damage to this product! Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over. 20070320 Set-Top Cable International Safety First Before using the set-top, read the Important Safety Instructions section of this guide. Explorer eClub The online Explorer eClub provides news and information about consumer products. Access the Explorer eClub on the Internet at the following Web address: Identify Your Set-Top Your service provider may ask for the serial number or the MAC address of the set- top if your system requires troubleshooting in the future. Look for the serial number and the MAC address on the bottom of the set-top. Write the serial number here: ____________________________________________ Write the MAC address here: ____________________________________________ 5 Mute volume Access last channel viewed Scroll through channels Access Navigator Bar Adjust volume Access specific channels Exit menus Access menus and EPG Access video-on-demand (VOD) window (if available from your service provider) Toggle between TV and Radio modes View channel options Access Electronic Program Guide (EPG) Access Setup Wizard Power On/Off Scroll through menu items (also used for VOD) Scroll through menu pages Select menu item T12721 About the Remote Control What’s on the Front Panel? 1 2 3 4 5 6 7 T12718 1 Power Turns the set-top on and off 2 LED Illuminates green when the set-top is on 3 LINK Illuminates green when there is a linked connection to an external modem for two-way communication between the set-top and the service provider (Available on Z70 models) 4 Guide Accesses the Electronic Program Guide (EPG) 5 OK Exits menus 6 Vol-, Vol+ Adjusts volume 7 CH-, CH+ Scrolls through channels What’s on the Back Panel? DC 12V INVideo Out Audio Out L R TV OutCable In Ethernet 1 2 3 4 5 6 7 T12719 1 Cable In Connects to the cable that delivers the signal from your service provider 2 TV Out Provides an RF output. Connects to TV 3 4 Audio Out L/R Video Out Connects to left/right audio of TV Connects to video input of TV 5 SIM Card Reader Reserved for future use 6 Ethernet Connects to Ethernet-equipped device (Available on Z70 models) 7 DC 12V IN Connects to an external power supply Connecting the Set-Top To connect your set-top to your entertainment devices, complete these steps. Connect your TV to the set-top. (See connection diagram.) Plug the set-top and the TV into a power source that is not controlled by a wall switch. POWER Do not turn on the set-top or TV yet. Wait for the green LED to illuminate. It may take several minutes for the set-top to receive the latest software, programming, and service information. Press POWER on the remote control. The first time you turn on the set-top, the Setup Wizard will start. Read and follow the directions on the screen to get your set-top ready for use. Connecting to a TV WARNING: Electric shock hazard! Unplug all electronic devices before connecting or disconnecting any device cables to the set-top. Back of Z70DVB Cable Input T12720 DC 12V INVideo OutAudio Out L R TV OutCable In Ethernet To Power Receptacle Back of TV RL AUDIOOUTVIDEOOUTAUDIO IN VIDEO IN CABLE IN AUDIO OUT VIDEO OUT Watch TV When you turn on the set-top, you will see a screen similar to this one until the set-top has downloaded the latest programming information. Setup Wizard The first time you turn on the set-top, you will see the Setup Wizard window. In the Setup Wizard you can select the language and screen settings for your set-top. Read and follow the directions on each screen of the Setup Wizard. If you want to change any of the settings at a later time, you can access the Setup Wizard by pressing the Setup key on the remote control. Set Parental Control PIN To set the Parental Control PIN, press the Setup key on the remote control and access the Expert Setup option. The first time you select this option, you must enter the Default PIN number (4321). The next time you access the Expert Setup option, you can enter a new PIN number that is more meaningful to you. Remember the PIN you choose because you will use it to block and unblock TV programs or channels for viewing. Press the number keys on the remote control to enter your PIN number, and then press the OK key on the remote control. Revert to Factory Settings All of your setup choices will be erased if you choose the Revert to Factory Settings option. Navigator Bar The Navigator Bar displays information a...
Эта инструкция также подходит к моделям:Спутниковые ресиверы - Z60DVBTM (1.39 mb)