Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
sauservice. com Satellite Installation Manual SEGA AMUSEMENTS USA INC. 010102010201000201020102014802 SECURING THE SATELLITE PLACEMENT POSITIONS A Be sure that all adjusters are placed against the floor. Failure to place the adjusters against the floor could lead to accidents caused by cabinet movement. Each satellite is equipped with 4 adjusters and 4 casters. When the placement position has been determined, place the adjusters directly against the floor and perform adjustments to make the satellite horizontally level. © Move the satellite to the placement position. © Remove the 2 screws at each corner to remove the lower covers. LEG COVER FRONT ADJUSTERS FIG. 6. 2 a BOTTOM VIEW OF THE SATELLITE PHOTO 6. 2 a 34 © Place all the adjusters against the floor. Use a wrench to adjust the height of the adjusters so that the satellite is horizontally level. © Following adjustment, tighten the nut on each adjuster to fix the height. Fasten upward. Be sure to make contact with the surface PHOTO 6. 2 b © Replace the 4 covers at the corners. FIG 6. 2 b Refer to this figure (scale: 1/100) for the layout of the place of installation. Follow the procedure below to attach the instruction plate and the instruction holder to the service door. Exercise caution, as the service door closes by its own weight, and can injure hands or fingers. Do not over-tighten the flange nuts, as this could damage the instruction plate. © Release and open the service door. ^8^ Secure the instruction plate to the service door using 6 carriage bolts and flange/cap nuts. Push the carriage bolts all the way through the holes, and tighten the 4 flange nuts from the inner side of the service door and the 2 cap nuts in the upside. CARRIAGE BOLT (6) 35 POWER SUPPLY, AND EARTH CONNECTION A • Be sure to independently use the power supply socket outlet equipped with an Earth Leakage Breaker. Using a power supply without an Earth Leakage Breaker can cause a fire when electric leakage occurs. • This product is designed for an electrical outlet with an earth element. The power cord incorporates an earth wire. Improper grounding could result in electrical shock to customers, damage to components, and/or malfunctioning. • If an electrical outlet with an earth element is not available and a commercially distributed conversion adapter is used, make sure that the product's earth terminal is connected to a grounded terminal using an earth wire. Improper grounding could result in electrical shock to customers, damage to components, and/or malfunctioning. • In order to ground securely, do not use the service outlet to supply the power of the other satellites. Improper grounding could result in electrical shock to customers, damage to components, and/or malfunctioning. (For TAIWAN) • The electric current capacity of the service outlet for the satellites is 10A max. Never use the service outlet for the machinery exceeding 10A. Using the machinery exceeding 10A can cause generation of heat and fire hazard. (For TAIWAN) • Ensure that the power cord and earth wire are not exposed on the surface (passage, etc.). If exposed, they can be caught and are susceptible to damage. If damaged, the cord and wire can cause electric shock and short circuit accidents. Ensure that the wiring position is not in the customer's passage way or the wiring has protective covering. The AC unit for the main projection unit is located at the back of the cabinet. The AC unit features a main switch, a circuit protector, an earth terminal, and an inlet for connecting the power cord. The AC unit for each satellite is also located at the back. These AC units feature a power switch, a circuit protector, an earth terminal, an inlet for connecting the power cord, and a service outlet. When connecting the satellite power source and earth, place the latch located at the end of the chain extending from the AC cover onto the hook located on the back of the satellite. This will secure the AC cover in the open position. When the work is finished, replace the latch onto the hook located on the back of the AC cover and close the cover. FIG. 6. 3 a 36 9 ) Ensure that the main switch is OFF. indoor earth terminal. FIG. 6. 3 b AC UNIT OF THE MAIN PROJECTION UNIT CIRCUIT PROTECTOR(10A)(For TAIWAN) FIG. 6. 3 c AC UNIT OF THE SATELLITE TO) Firmly insert the power plug into the socket outlet. Insert the opposite side of the power cord plug to the AC unit's connector (INLET). 37 © © One end of the earth wire should be connected to the product's earth terminal, and the other end to an indoor earth terminal. The earth terminal of the AC unit consists of a bolt and nut set. First remove the nut, then place the end of the earth wire so that the bolt passes through, and finally tighten the nut. (For TAIWAN) *Note that the earth wire is incorporated in the power cord for the areas of AC 120 V (...