Оценок - 0, средний балл: 5
(
)
)
|
Фрагмент инструкции
Controls and Buttons This section also describes the controls located on the front and back of the receiver. Programming the Remote Control Your remote capable of controlling other devices as well. This section tells you how to program the remote to control TVs, VCRs, Laserdisc players, and other equipment. REFERENCE Parts of the DSS® System One way to understand the DSS® system is to look at the different parts of the system—from the studio down to the satellite receiver and remote control in your home. World View These parts make up the DSS® system “big picture.” Uplink Center Authorization Center Satellite Satellite Dish Antenna a Uplink Center Transmits programming up to the satellite. Satellite Relays the programming signals back to your satellite dish. The satellite is parked above the equator, in geostationary orbit 22,300 miles above the earth. Satellite Dish Antenna Receives the satellite signals. Because the satellite is so powerful, the dish can be as small as 18 inches. Program Provider Authorization Center Processes billing statements. Your DSS® system is linked to the Service Center through the phone jack on the back of your satellite receiver. REFERENCE Home View These parts are inside of or attached to your house. Satellite Dish DSS Receiver Telephone Jack Remote Control Access Card and Security Clip Satellite Dish Picks up the satellite’s coded program information and relays it to your satellite receiver. (Your satellite dish may be installed in different locations on or around your house. The satellite dish must, however, be pointed in a southern direction toward the satellite.) Satellite Receiver Receives the TV program information and sends it to your TV or VCR. Telephone Jack Connects to the phone jack on the back of the satellite receiver. The satellite receiver uses a toll-free number once a month to update your access card. This update only takes a few seconds and ensures that you will have continuous service. The system automatically hangs up if you pick up the phone when the satellite receiver is calling out. Television If your television is remote controllable, you can program the remote to change channels and volume. Home Theater Universal Remote (included with your DSS® system) Controls the DSS® system as well as most remote controllable TVs, VCRs, and other devices. You may need to program the remote to control specific brands of devices you own. Access Card (installed in satellite receiver) Must be inserted for you to use the DSS® system! Provides system security and authorization of DSS® services. Do not remove the card except when issued a new card as a replacement for the original. REFERENCE Controls and Buttons This part of the Reference sections discusses the controls and buttons located on the receiver and the remote control. MENU SELECT POWER RECALL TV/DSS Slide open the door to get to the Access Card. Front Panel Controls POWER Turns the satellite receiver’s power on or put the unit into standby mode. RECALL Brings up the on-screen channel marker. TV/DSS Switches the source of the video signal from DSS® satellite signals to an off-air antenna or cable signal (if you are using RF output from the satellite receiver). ARROWS Press the navigation arrows to move the on-screen highlight up, down, left, or right. Using the arrows to highlight a menu item is also called “pointing.” MENU/SELECT Brings up the Main Menu. If you are already in the menu system (or a program guide), press MENU/SELECT to select a highlighted choice. ACCESS CARD Identifies you to your program providers. The DSS® system requires a valid access card. REFERENCE OUT TO TV IN FROM ANT S-VIDEO VIDEO R LAUDIO WIDE BAND DATA VCR CONTROL REMOTE IN SATELLITE IN LOW SPEED DATA PHONE JACK CH 3 CH 4 Back Panel IN FROM ANT Use to connect an off-air antenna or cable TV signal to the DSS® system. OUT TO TV Use to connect the satellite receiver to your TV. However, if your TV has audio/video jacks, you should use those jacks to get better picture and sound quality. CH3/CH4 SWITCH If a coaxial cable is used to connect the satellite receiver to your TV, you must set the CH3/CH4 SWITCH. For example, to see the DSS® signal on TV channel 3, set the switch to 3. S-VIDEO Provides the best picture quality. If your TV has S-VIDEO capability, use this jack along with the audio/video input jacks to connect the satellite receiver to your TV. VIDEO Provides better picture quality than the OUT TO TV jack. If your TV has audio/video capability, use this jack to connect the satellite receiver to your TV. You must also connect the AUDIO jacks. AUDIO (R and L) Provide better sound quality than the OUT TO TV jack. If your TV has audio/video capability, use these jacks to connect the satellite receiver to your TV. You must also connect the VIDEO jack. WIDE BAND and LOW SPEED DATA PORTS These ports allow you to connect the DSS® system to future services and accessories as they become available. A shielded cable and additional hardware may...