Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
Safety • Read the instructions in this manual carefully before you connect, install and use the product. • Keep this manual for future reference. • The product is for indoor use only. • Do not use the product close to water. • Do not expose the product to extreme heat. • In case of technical difficulties, do not open the product. Bring it to your Philips dealer. • Do not cover the product. • Connect the power adapters only to a 220-240 V AC/50 Hz power supply. • The product can cause interference to other equipment. Check if any equipment near the product can be affected before you start using it. EN EN Installation Remove interference on TV3 1 Find the CHANNEL switch on the transmitter. 2 Check the setting of the CHANNEL switch. 3 Find the CHANNEL switch on the receiver (A). 4 Set the CHANNEL switch to the same number as on the transmitter. For basic installation, see the quick start guide that came with your Wireless TV Link. L Channel DC 12V 1 2 3 4R CHANNEL 1 2 3 4 Make sure to set the CHANNEL switch on both the original and the new receiver. Operation Enjoy your Wireless TV Link For basic installation, see the quick start guide that came with your Wireless TV Link. Operation Operation EN Watch a cable TV program on TV3 STANDBY SELECT SLV5400 WIRELESS TV LINK TRANSMITTER WIRELESS TV LINK RECEIVER Your VCR or DVD recorder needs to be connected to the transmitter (A) of the Wireless TV Link and connected to the Cable-TV signal. 1 2 3 4 Switch on the transmitter. Switch on the VCR or DVD recorder. Take the remote control of the VCR or DVD recorder with you. Go to TV3. 5 6 Switch on TV3. Switch on the receiver (A). 7 8 Press + or - on the receiver (A) to select the VCR or DVD recorder; or: press 4 on the remote control. Select the channel on the VCR or DVD recorder with its remote control. Turn off the auto standby mode when you use the VCR or DVD recorder to watch a cable tv program. Refer to the user manual of the VCR or DVD recorder. If the VCR or DVD recorder records a television program, you watch the recorded channel. EN EN Troubleshooting Problem Tip No image or wrong • Make sure SCART cables are image on TV3 firmly inserted. • Make sure the receiver (A) is connected to TV3. • Make sure both receiver (A) and transmitter are switched on. • Make sure the video source is switched on. • Make sure the correct SCART input on TV3 is selected. • Select the correct video source with +/- on the receiver (A). > In combination with the SLV5400 transmitter. • If the video source gives proper image on TV1: Make sure the video source gives video signal in CVBS mode. See its user manual • Change the wireless channel that is used for communication. See page 6. • The receiver (A) is out of range of the transmitter. The number of walls and ceilings in between the receiver (A) and transmitter restrict the distance. Interference in the image on TV3 • Slightly change the position of the receiver (A) or the transmitter. • Change the wireless channel that is used for communication. See page 6. • The receiver (A) is out of range of the transmitter. The number of walls and ceilings in between the receiver (A) and transmitter restrict the distance. Troubleshooting Troubleshooting EN Problem Tip The video sources do not respond to the remote control commands from TV3 • Point the remote control directly to the receiver (A). • Replace the batteries of the remote controls with new ones. • Install the remote control blaster cord. See the user manual of the Wireless TV Link. • The maximum operating distance of the remote control is 5 m. The image of the • Turn off the auto standby mode video source dis-of the video source. See its user appears on TV3 manual. • Follow the instructions to reconnect the video sources. See the quick start guide. Buzzing sound • Slightly change the position of the when you use the receiver or the transmitter until remote control. the buzzing sound stops. • Sometimes it is not possible to solve the problem. Black and white • Check if the SCART connector of image with S-VHS the S-VHS VCR gives signal in VCR. CVBS. See its user manual. EN EN Information Health and safety The product transmits and receives radio waves when it is switched on. The product complies with the standards that are defined for it. The quality of the image can be influenced by the use of microwave ovens. Other wireless systems (Bluetooth, wireless networks etc.) can also have influence on the quality of the image. The product is based on RF technology. Therefore the product can suffer from the same kinds of interference as GSMs, portable radios and other RF-based products. Maintenance and service If your product is defective and needs repair, but your warranty period has expired, you can consult our specialists (see the rear page) Recycling and disposal All redundant packaging material has been omitted. Your set consists of materials that can be recycled if disassembled by a specialized company. Please observe the local regulations re...
Эта инструкция также подходит к моделям:Сетевое оборудование - SLV5405/00 (236.03 kb)