Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
SAFETY INSTRUCTIONS - IMPORTANT NOTES The antenna will be lowered within 12 seconds of the ignition being switched on (if the unit is in stand-by mode or the UFS 740sw is switched off). Otherwise the control unit that is in use is lowered immediately. Attention: Lowering the antenna can take up to 30 seconds after the ignition is switched on! Checks before commencing a journey • Before commencing a journey, the antenna must always be lowered into horizontal position (park position). If the antenna has collided with a fixed or movable object, check that it is still securely attached. • As the antenna is subjected to vibration loads during driving, at regular intervals, depending on the frequency of driving, you should check that the system is still securely fitted and tighten any parts that have come loose. • The maximum permissible speed for vehicles with a receiver unit mounted on the roof and the antenna lowered is 130 km/h. • Lower the antenna if it will not be used for a long period. This makes the securing bolts more diffi cult to access (protection against theft). Safety precautions during installation During installation of the turntable, make sure that no persons, in particular children, are in the immediate vicinity of the turntable and that they cannot touch any moving parts – danger of crushing! Always unplug the power supply during installation work. Antenna in the park position whilst driving The antenna must always be lowered into horizontal position (park position) while driving. As a reminder, please attach the sticker from the supplementary sheet “Lower the CAP 600 antenna while driving” where it can easily be seen by the person operating the ignition switch. Risk of accidents due to exceeding normal vehicle height by failure to lower antenna! The driver is responsible for the condition of external fittings on the vehicle! In addition the instructions in the installation and operating manuals for these devices and for the attachments and superstructures must be complied with at all times! If stormy weather is expected, the turntable must always be moved to the park position, otherwise both the CAP 600 and the vehicle may be damaged. INSTALLATION AND CONNECTION REQUIRED TOOLS AND EQUIPMENT • Circular cutter, O 38 mm • Flat-bladed screwdriver for M5 screws • Power drill • Galvanised round head screws, depending on the roof structure (O: 5 mm, sheet metal screws D 7981, depending on the roof structure) or round head screws D 7985 with washers and nuts • Twist drill, O 2.5 or 5.5 mm • Round file and/or emery paper • Cleaning agent • Open-ended or ring spanners 10 and 11 mm across flats • Knife • Cross-head screwdrivers for M3 and M5 screws • Torque wrench capacity 6 to 11 Nm • Hexagon socket key (5 mm) • Two wooden beams for supporting the turntable UNPACKING AND PREPARATION Keep the device in its cardboard box for transport on to the vehicle roof. Only take the turntable out of its packaging when it is on the vehicle roof. Retain the original packaging, as if it is necessary to send the unit for repair transport damage cannot be ruled out and the manufacturer accepts no liability for possible damage. Loosen the six fastening screws (width A/F: 10 mm). Carefully lift the turntable off the mounting plate and place it on the prepared wooden supports. Make sure that the cables are not crushed where they emerge from the underside of the turntable. SELECTING THE INSTALLATION LOCATION Essentially, the cable lengths of the MobiSet 2 CAP 600 components allow you a free choice of installation location on your caravan or motor home. However, you should take note of the following points: • Before installation, you should find out whether the operating manual for your vehicle permits the fitting of non-vehicle specific parts or what requirements need to be met in order to do so. • For direct satellite reception, there should not be any obstructions between the antenna and the satellite. Therefore, make sure that the antenna is not shadowed by roof extensions such as luggage racks, air conditioning units, solar panels, etc. The problem of shadowing applies also to the selection of the parking place for your vehicle. For interference-free satellite reception, the antenna needs a projected free view to the South at an angle of between 15° and 55° (depending on location) to the horizontal. INSTALLATION AND CONNECTION • When selecting the installation position, take into account the range of movement of the turntable (see graphics and the “Technical Data” chapter). There must be no structures on the roof that would obstruct this range of movement (risk of collision). For safety, keep at least the required area free (for ease of installation and any subsequent dismantling). Roof rail Area (min. O 690 mm) within which the turntable with its height of up to 120 mm can be attached Roof attachments may be mounted within the hatched area. The height of neighbouring attachments on the roof may lead to shadowing! Direc...