If you have questions regarding the contents of the manual, please contact our Technical Service Department at ACR Electronics, Inc., Telephone +1 (954) 981-3333. Please be ready to provide the technician with the page number you wish to discuss. If you have a question that is not covered in the manual, please visit our website and access the Frequently Asked Questions (FAQs) section for further information or call our Technical Service Department. The website address is If in the future you los

29-45 and 29-66Initial Lumens – 302Lamp No. 29-45 and 29-6615FEETLEFTFEETRIGHT15FEET FROM LAMP (Measured on axis) 01FCLAMPAXIS15FEETLEFTFEETRIGHT15FEET FROM LAMP (Measured on axis) 0LAMPAXIS0.50.30.21FC0 20 30 40 50 60 0 20 30 40 50 60 0.10.5 0.3 0.2 0.1 TECHNICAL DATA HeadsAll metal formed aluminumlampheads.The die cast metalthree dimensional swivelassembly permits approximateaiming adjustment from 80° vertical and 358°rotation. Theplacement is secured with alockable pivot mounted on arotating

The demodulated 121.5 MHz audio signal is annunciated at all times. If there is not any signal on the 121.5 MHz carrier, whether activated beacon or other source, static will be audible. The speaker volume is high, and the signal strength meter is active. Monitor Low mode This mode is identical to the Monitor High mode except that the speaker volume is lower. NOTE: The ARX-50 reverts back to Alarm mode after 15 minutes in Monitor High mode. Training mode Operation in Training mode is identical t

If someone attempts to register a PLB reported as stolen, NOAA or your national authority will notify the appropriate police department. APPENDIX A - ACCESSORIES 1. Multi-Function Belt Clip The SARLink™ comes standard with a multi- function belt clip. To install the clip, simply align the bottom tabs on the clip with the insert holes located on the bottom of the beacon. Snap the clip in place by pressing the top of the clip so that the two top tabs engage in the two insert holes on the top of th

Repeated activations could be viewed as a hoax. 11. Preventing false alerts A false alert is any activation of the beacon, intentional or otherwise, that does not result from a situation of grave and imminent danger. Be sure to do the following to help minimize false alerts: . Register your beacon. This does not reduce false alert rates; however, when the beacon is properly registered, the situation can usually be resolved with a phone call. . Be careful with whom you leave your beacon. Make sur

1339 and 1341 I. APPROVAL CONDITIONS and CARRIAGE REGULATIONS This inflatable PFD is approved by the U.S. Coast Guard for use as a Type V Humidity Sensitive Personal Flotation Device (PFD) with Type II performance. IT IS APPROVED ONLY WHEN WORN. It is not approved for water skiing or other high impact, high speed activities. This inflatable PFD was designed to be more comfortable and less restrictive to wear than inherently buoyant PFD’s. When worn, used, and serviced according to this owner’s m

6 DONNING and INFLATION INSTRUCTIONS After completing the pre-donning check, follow these instructions to don, inflate and adjust the PFD for maximum performance. 1. Loosen Shoulder Straps. Insert left arm between back strap and deflated vest (See fig.1). Pull vest on over your head (See fig.2). Pull buckle to front so you can see it. Buckle and adjust by pulling on free end of the belt. Secure the excess strap by tucking it under the belt. Always position the belt with the center window in fron

Through constant innovation and the application of new technologies, Mustang is the leading supplier of quality flotation and hypothermia protection products to the most demanding users – from fishermen, sailors and power boaters to the Coast Guard, jet fighter pilots and even NASA astronauts. The best Personal Flotation Device (PFD) is the one you wear. There are many choices when it comes to picking the PFD that will keep you safe on the water. For some activities foam vests are a great choice

Ft. Over-the-Range Microwave Oven HOOD EXHAUST DUCT: Outside ventilation requires a HOOD EXHAUST DUCT. Read the following carefully. EXHAUST CONNECTION: The hood exhaust has been designed to mate with a standard 3-1/4" x 10" rectangular duct.lf a round duct is required, a rectangular-to-round transition adaptor must be used. Do not use less than a 6" diameter duct REAR EXHAUST: If a rear or horizontal exhaust is to be used, care should be taken to align exhaust with space between studs,or wal