Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
2 Slide the battery into place. Keep all miniature SIM cards out of the reach of small children. The SIM card and its contacts are easily damaged by scratches or 3 Slide the cover back into place Charge the battery 1 Connect the lead from the charger to the bottom of the phone. [ 10 ] Before you begin 2 Connect the charger to a standard wall outlet. The battery power indicator (or battery bar) appears on the screen and starts scrolling. If the Battery bar phone is on, Charging appears also. Note: If the battery is completely empty, it might take a few minutes before the battery bar appears on the screen. Tip: You can use the phone while it’s charging. 3 When the battery bar stops scrolling, the battery charge is complete. Battery full appears also, if the phone is on. Note: The charging time depends on the charger and battery that you use. For example, the charging time for the BLB-2 battery with the ACP-8U charger is about 1 hour and 40 minutes. 4 Disconnect the charger from the phone. Remove the battery 1 Switch off the phone. 2 Press the top of the back cover and the back cover release button, then slide off the cover. 3 Lift out the battery. [ 11 ] 3. About your phone • Switch on your phone • Press and hold power for more than a second. The phone might ask for a Personal Identification (PIN) code or a security code. See “PIN and PUK codes” on page 66 for more information. Warning! Do not switch on the phone in places where wireless phone use is prohibited or where the use of the phone could cause interference or danger. Tip: As with any other radio transmitting device, do not touch the antenna unnecessarily when the phone is switched on. Contact with the antenna affects call quality and might cause the phone to operate at a higher power level than needed. [ 12 ] About your phone • About the Start screen When you turn on your phone, the first screen that appears is the Start screen. In the middle of the Start screen, you see information indicating which wireless network your phone uses. This information can vary between phones. Other indicators and icons appear on this Start screen and are described in the next section. About indicators and icons On your phone, you have two types of identifiers: indicators and icons. Indicators Indicators show the status of something. The phone uses three types of indicators: • Signal strength indicator: Shows the strength of the signal to your phone. • Battery power indicator: Shows how much power is left in your phone’s battery. • Volume indicator: Shows the earpiece volume level. Adjust the volume level with the earpiece volume buttons on the left side of the phone (see “Adjust the earpiece volume during a call” on page 17). [ 13 ] Icons Icons are graphical representations of a specific item or situation. For example, this icon appears when you have a voice message waiting to be heard. (Some systems use a different method.) The rest of this section shows examples of each icon that can appear on your phone and tells you what these icons indicate. Line 1 is selected for outgoing calls. Line 2 is selected for outgoing calls. You have an active call. You have one or more new voice messages. You have one or more new text messages. (If blinking, text message memory is full.) Keyguard is on. Your phone will not accept any key presses. The alarm clock is set. The Silent profile is selected. Incoming voice calls are being forwarded to another number. You have forwarded all voice calls received on line 1. You have forwarded all voice calls received on line 2. You have forwarded all voice calls received on lines 1 and 2. The phone is ready for you to enter a response. Characters entered will be uppercase letters. Press to switch letter case. [ 14 ] About your phone Characters entered will be lowercase letters. Press to switch letter case. Characters entered will be numbers. (When entering letters, switch to numbers by pressing and holding .) You are in “special character” mode. Select a character, then press Use. (When entering letters, switch to special characters by pressing the key.) You are in predictive text mode. You are in predictive text mode. Characters entered will be uppercase letters. Press to switch letter case. You are in predictive text mode. Characters entered will be lowercase letters. Press to switch letter case. You are in predictive text mode. Characters entered will be numbers. Indicates the current call. Indicates a call on hold. [ 15 ] 4. Making and answering calls This chapter tells you how to make and receive calls and how to adjust certain options. • Make a call Check the signal strength The signal indicator on the left side of your phone’s screen shows the strength of the network radio signal. The indicator scrolls as the signal strength increases and decreases. To get the strongest signal, try moving your phone slightly. If you’re inside a building, move toward a window. Use the keypad 1 Enter the area code and phone number. 2 Press . Hold the phone a...