961 95 00-01 22 18 21 53 19 28 19 55 28 19 55 54 54 6 6 5 6 6 9 12 7 7 8 6 11 27 27 30 26 25 20 23 24 31 25 24 26 23 29 21 53 19 20 18 10 4 13 14 16 15 36 37 50 47 42 44 27 43 46 38 45 4327 41 42 40 39 34 32 49 19 48 51 33 35 56 REPAIR PARTS AUGER HOUSING / IMPELLER ASSEMBLY SNOW THROWER - MODEL NO. 10530SBE (96195000101), PRODUCT NO. 961 95 00-01 KEY PART NO. NO. DESCRIPTION 4 532 19 10-79 Pulley, Impeller 532 18 89-09 Bearing Assembly, Flange 6 532 15 53-77 Nut, Hex Flange 5/16-18 7 532 18 03-

NO. DESCRIPTION 1 178875X479 Lever, Auger Control, RH 2 178648X479 Lever, Traction Drive Control, LH 3 179439 Nut, Cage 1/4-20 4 178888 Bushing, Flange 5 169675 Retainer, Hairpin 6 180402 Screw, Hex Head 1/4-20 x 3/4 7 178652 Rod, Interlock 8 184003 Tube Assembly, Interlock, RH 9 178651 Tube Assembly, Interlock, LH 10 178645X479 Panel, Control 11 74780524 Screw, Hex Head 5/16-18 x 1-1/2 12 74780528 Screw, Hex Head 5/16-18 x 1-3/4 13 178646X479 Handle Tube, LH 14 178696X479 Handle Tube, RH 15 738

Use a stick, NOT YOUR HANDS, to un clog the chute and/or auger. The DIRECTION in which snow is to be thrown is controlled by the discharge chute control lever. • To change the discharge chute position, press downward on discharge chute control lever and move lever left or right until chute is in desired position. Be sure lever springs back and locks into desired position. The DISTANCE that snow is thrown is controlled by the position of the chute deflector. Set the deflector low to throw snow a

NOTE: The multi-wrench may be used for assembly of the chute rotator head to snow thrower and making ad just ments to the skid plates. UNFOLD UPPER HANDLE 1. Raise upper handle to the operating position and tight en handle knobs securely. INSTALL SPEED CONTROL ROD (See Figs. 1 and 2) 1. Remove plastic tie securing rod to lower handle. 2. Insert rod into speed control bracket and secure with retainer spring. SPEED CONTROL ROD HANDLE KNOB LOWER HANDLE PLASTIC TIE UPPER HANDLE FIG. 1 SPEED CON TROL

5. Contact a qualified service center. Excessive vibration 1. Loose parts or damaged augers or impeller. 1. Tighten all fasteners. Replace damaged parts. If vibration remains, contact a qualified service center. Recoil starter is hard to pull 1. Frozen recoil starter. 1. See “If Recoil Starter Has Frozen” in the Operation section of this manual. Loss of traction drive / slowing of drive speed 1. Drive belt is worn. 2. Drive belt is off of pulley. 3. Friction drive wheel is worn. 1. Check / repla

inches 1 inch = 25.4 mm 21 22 REPAIR PARTS SNOW THROWER - MODEL NUMBER P8527ESA CONTROL PANEL / DISCHARGE CHUTE 3 2 1 1 2 6 7 4 5 6 16 18 17 10 11 14 13 3 8 15 8 9 12 19 2 2 21 21 22 23 14 26 28 27 27 25 20 29 24 22 23 REPAIR PARTS SNOW THROWER - MODEL NUMBER P8527ESA CONTROL PANEL / DISCHARGE CHUTE KEY PART NO. NO. DESCRIPTION 1 183334 Knob, Lever 2 17501010 Screw #10-24 x 5/8 3 178674 Control Assembly, Deflector 4 73800600 Nut, Lock 3/8-16 5 19131316 Washer, Flat 3/8 6 178659 Control Assembly,

inches 1 inch = 25.4 mm 21 22 REPAIR PARTS SNOW THROWER - MODEL NUMBER P524ESA CONTROL PANEL / DISCHARGE CHUTE 1 2 6 7 4 5 6 8 8 19 2 2 14 26 28 27 27 25 20 29 24 18 13 14 3 11 12 11 9 14 16 17 15 10 REPAIR PARTS SNOW THROWER - MODEL NUMBER P524ESA CONTROL PANEL / DISCHARGE CHUTE KEY PART NO. NO. DESCRIPTION 1 183334 Knob, Lever 2 17501010 Screw #10-24 x 5/8 3 179096X479 Strap, Slotted 4 73800600 Nut, Lock 3/8-16 5 19131316 Washer, Flat 3/8 6 178659 Control Assembly, Chute Rotater 7 178638X479 S

NOTE: The multi-wrench may be used for assembly of the chute rotator head to snow thrower and making ad just ments to the skid plates. UNFOLD UPPER HANDLE 1. Raise upper handle to the operating position and tight en handle knobs securely. INSTALL SPEED CONTROL ROD (See Figs. 1 and 2) 1. Remove plastic tie securing rod to lower handle. 2. Insert rod into speed control bracket and secure with retainer spring. SPEED CONTROL ROD HANDLE KNOB LOWER HANDLE PLASTIC TIE UPPER HANDLE FIG. 1 SPEED CON TROL

Tighten securely. 2. Install remote cable eyelet to chute deflector with 1/4-20 shoulder bolt, 1/4 flat washer and 1/4-20 locknut as shown. Tighten securely. 3. Install spring hooks between hex nuts on chute rotater head and into hole in chute deflector as shown. HOOK BE TWEEN HEX NUTS ON CHUTE ROTATER HEAD SPRINGCHUTE DE FLEC TOR 5/16-18 CARRIAGE BOLT 5/16-18 LOCKNUT REMOTE CABLE BRACKET 1/4-20 LOCK- NUT 5/16 FLAT WASHER CABLE EYELET 1/4 FLAT WASHER 1/4-20 SHOULDER BOLT FIG. 8 CHUTE DEFLECTOR C

The only time the lubricant needs attention is if service has been performed on the gear case. • If lubricant is required, use only Ronex ED #1 grease. TRACTION DRIVE SYSTEM DO NOT lubricate the drive components inside the snow thrower. The sprockets, hex shafts, drive disc and friction wheel require no lubrication. The bearings and bushings are lifetime lubricated and require no maintenance. CAUTION: Any lubricating of the above com po nents can cause contamination of the friction wheel and dam