ITEM Spark plug gap Valve clearance Other specifications MAINTENANCE Refer to page: 45 See your authorized Honda dealer 0.028 0.031 in (0.7 0.8 mm) IN: 0.15 0.02 mm EX: 0.20 0.02 mm (varies with snow conditions) (varies with snow conditions) Specifications are subject to change without notice. .. .. .. .. .. .. .. 71 TECHNICAL & CONSUMER INFORMATION Frame Engine Tuneup HS928 TA TAS WA WAS SZAS 28.5 in (725 mm) 40.9 in (1,038 mm) 41.0 in (1,042 mm) 231 lbs (105 kg) 240 lbs (109 kg) 28.0 in (710 m

To ensure proper engine operation, the spark plug must be properly gapped and free of deposits. If the engine has been running, the muffler will be very hot. Be careful not to touch the muffler. SPARK PLUG 1. Remove the spark plug cap. WRENCH 2. Clean any dirt from around the spark plug base. 3. Use the spark plug wrench supplied in the tool kit to remove the spark plug. 4. Inspect the spark plug. Replace it if the electrodes are worn or if the insulator is cracked, chipped, or fouled. .. .. ..

Other uses can result in injury to the operator or damage to the snowblower and other property. Most injuries or property damage with snowblowers can be prevented if you follow all instructions in this manual and on the snowblower. The most common hazards, are discussed below, along with the best way to protect yourself and others. Avoid Rotating Auger The snowblower auger can cause serious cuts and even amputate fingers, hands, toes, or feet. Keep away from the auger whenever the engine is runn

Normally, any problems concerning the product will be handled byyour dealer's' servicedpeartment. If you have a warranty problem that hasnot been handled to your satisfaction, we suggest you take the following action: Discuss your problem with a member of dealership management. Often complaints can be quickly resolved at that level. If the problem has already been reviewed with the ServiceManager, contact the owner of the dealership or the General Manager. If your problem still has not been reso

Let the snowblower works its way through deep drifts. If the travel speed of the lawn tractor is too fast, the snowblower may become overloaded and clog. For best results, raise the snowblower and remove a top layer of snow. A second pass will remove the remaining snow. Always operate the lawn tractor with the throttle set to^ (FAST). Using other throttle settings can reduce performance and clog the discharge chute. POP 52152 (9610) 29 Removing the Snowblower SB2040 Snowblower Removing the

Honda Power Equipment Mfg., Inc. reserves the right, however, to discontinue or change specifications or design at any time without notice and without incurring any obligation whatever. INTRODUCTION Congratulations on your selection of a Honda snowthrower. We are certain you will be pleased with your purchase of one of the finest snowthrowers on the market. We want to help you get the best results from your new snowthrower and to operate it safely. This manual contains the information on how

Loosen (don’t remove) the drain screw until the fuel starts to drain. Drain until the fuel tank is empty, then tighten the drain screw. A WARNING Gasoline is highlyflammable and explosive. You can be burned or seriously injured when handling fuel. • Keep heat, sparks, and flame away. • Handle fuel only outdoors. • Wipe up spills immediately. 32 STORAGE Engine Oil 1. Change the engine oil (page 24). 2. Remove the spark plug (page 25). 3. Pour a tablespoon (5 ~ 10 cc) of clean engine o

Maintenance, replacement, or repair of the emission control devices and systems may be performed by any engine repair establishment or individual, using parts that are ‘‘certified’’ to EPA standards. .. .. .. 35 SERVICING YOUR SNOWBLOWER MAINTENANCE SAFETY Injury from moving parts. Burns from hot parts. Carbon monoxide poisoning from engine exhaust. Safety Precautions Some of the most important safety precautions follow. However, we cannot warn you of every conceivable hazard that can arise in p

3. After adjustment, retighten the ten- sion bolt lock nuts. TENSION BOLT 8. 8. I / i- i Before storing the snowblower for an extended period: 1. Be sure the storage area is free of excessive humidity and dust. 2. Drain the fuel - m Gasoline is extremely flammable and explosive under certain conditions. Do not smoke or allow flames or sparks in the area. FUEL ‘VALVE a. Drain the fuel. CARBURETOR DRAIN SCREW b. Loosen the carburetor drain screw, and drain the gasoline into a suitable container. R

Maintenance Follow the Maintenance Schedule on page 21. Remember that this schedule is based on the assumption that your machine will be used for its designed purpose. Sustained high-load operation will require more frequent service. TECHNICAL & CONSUMER INFORMATION Air Index An Air Index Information hang tag/label is applied to engines certified to an emission durability time period in accordance with the requirements of the California Air Resources Board. The bar graph is intended to provide y