Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
Pulley will not be re-used in this installation. 6. See figure 3. Replace the two 3/4 taptite screws as shown with two 5/16-18 x 1-1/2 taptite screws supplied. 7. See figure 4. Position the pulley bracket assy. (A) on the 1-1/2 taptite screws installed in step 6. Install the double groove pulley (B) to the arbor shaft. Reinstall the capscrew, lockwasher, and large flat washer removed in step 5. Torque capscrew to 50-70 ft.-lbs. (68-76 Nm). 8. Mfg. No. 1691867 only. See figure 4. Install new belt stop (C) to pulley bracket with the short leg towards Figure 3. A. Taptite Screws A. Bracket Assy. C. Belt Stop B. Pulley (Mfg. No. 1691867 only) A. Deflector Support Rod C. Carriage Bolt B. Pivot Bracket 5/16-18x3/4 4 Turbo Installation - 38" Mower Deck the front of deck. Secure using hardware removed in step 4. (A new nut and lockwasher is supplied with this kit and can be used in place if existing hardware). Tighten all hardware securely. Mfg. No. 1692626. See figure 4. Install pulley bracket (A) using hardware removed in step 4. (A new nut and lockwasher is supplied with this kit and can be used in place if existing hardware). Tighten all hardware securely. 9. See figure 5. Install the new deflector support rod (A) underneath the pivot bracket (B) and install bracket to deck. Secure bracket with two carriage bolts (C), installed from underneath deck. 10. See figure 6. Turn deflector over and locate the drill-points for mounting the support rod (A, figure 6). Drill four 13/64" holes. Install deflector to new support and secure with screws and nuts as shown in figure 1. 11. Mfg. No. 1691867. See figure 7. Install support brace assy. (A) to rear surface of deck. Secure with two taptite screws (B). See figure 8. Adjust spring latch (A) so it overlaps the top edge of deflector by 1/4" - 3/16“, in the down position. Mfg. No. 1692626. See figure 9. Install the capscrew (A) from inside the mower deck. Install the washer (B), knob (C) and locknut (D). 12. Install mower deck to tractor. See the tractor Operator’s Manual. See figure 10 for steps 13-18. 13. Install spindle (A) of turbo housing (B) into pivot bracket (C). 14. With right hand, hold both strands of the turbo belt around turbo idler pulley (F). Pull belt loop and belt tension arm (D) fully forward and hold in this position. Figure 7. Mfg. No. 1691867 only. A. Support Brace Assy. C. Wingnut B. Taptite Screws Figure 8. Mfg. No. 1691867 only. A. Spring Latch C. Capscrews B. Deflector Edge Figure 9. Mfg. No. 1692626 only. A. Carriage Bolt C. Knob 5/16-18 x 1-1/2 D. Locknut, 5/16 B. Washer 5 Turbo Installation - 38" Mower Deck 15. Lift deflector to maximum raised position. Rotate turbo into position, making sure it fits securely over carriage bolt (A, figure 9) or wingnut assy. (E, figure 10). Make sure belt is clear of all brackets. 16. Put belt in lower groove of pulley (H), then around fixed idler pulley (G). Release the belt tension arm (D). 17. Check to be sure belt is routed around all pulleys correctly. 18. With turbo housing in position, tighten wingnut or knob (E). Put mower drive belt into top groove of double-groove pulley and on engine PTO pulley. Figure 10. Mfg. No. 1691867 shown A. Spindle E. Wing Nut or Knob B. Turbo Housing F. Turbo Idler Pulley C. Pivot Bracket G. Fixed Idler Pulley D. Belt Tension Arm 6 Turbo Installation - 44" Mower Deck Ref. Description Qty. Ref. Description A. Turbo Blower Assy. 1 N. Support Brace Assy. В. Deflector Rod Support 1 0. Belt Cover C. Capscrew, Truss Hd., 10-24 x 3/4 4 P. Pulley, Double Groove D. Nut, Nylock, 20-24 4 Q. Capscrew, 7/6-14 x 2 E. Pivot Bracket 1 R. Washer, 5/16 F. Carriage Bolt, 5/16-18 x 3/4 1 S. Spacer G. Screw, Whizlock, 5/16-18 x 1/2 1 T. Capscrew, 5/16-18 x 1-1/2 H. Baffle Assy. 1 U. Locknut, Flanged I. Idler Pulley Assy. 1 V. Stud, 5/16-18 x 5-1/2 J. Capscrew, 5/16-18 7/8 2 W. Washer, 5/16" I.D. x 7/8" O.D. K. Lockwasher 1 X. Washer, 5/16" I.D. x 1" O.D. L. Nut, Nylock, 5/16-18 2 Y. Roller, Replacement M. Belt Stop 1 Qty. 2 2 1 Turbo Installation - 44" Mower Deck A. Baffle Assy. E. Lockwasher, 5/16 B. Bracket F. Nut, 5/16-18 C. Spacer D. Carriage Bolt, 5/16-18 x 1-1/4 1. Remove the mower deck from the tractor. See your tractor Operator’s Manual for procedure. 2. Remove the deflector from the the deck and retain hardware. Remove and discard the plastic plug from mower deck housing. 3. See figure 2. Install baffle assy. (A) to the stone guard (underneath mower deck) using U-bracket (B), spacer (C) carriage bolt (D), lockwasher (E) and nut (F). Reuse hardware removed in step 2 to secure tab on baffle assy, to mower deck. On LT/1600 series tractors, remove arbor cover and upstop. Retain flat washer and upstop. Arbor cover and taptite screws will not be used in this installation. 4. Remove the mower belt from right-hand pulley. 5. Remove the right-hand pulley and retain the lockwasher and large washer. Pulley will not be re-u...
Эта инструкция также подходит к моделям:Снегоочистители - 1691868 (1.05 mb)
Снегоочистители - 1692030 (1.05 mb)
Снегоочистители - 1692626 (1.05 mb)