Оценок - 3, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
grounded system. Ask a licensed electrician if you are unsure. If you have a grounded three-prong receptacle, proceed as follows. If you do not have the proper house wiring, DO NOT use the electric starter under any conditions. Insert ignition key fully into slot. Make sure it snaps 2. into place. DO NOT turn ignition key. The engine cannot start unless the key is inserted into ignition switch. Plug the extension cord into the electric switch 3. box located on the engine. Plug the other end of extension cord into a three-prong 120-volt, grounded, AC outlet in a well-ventilated area. Move throttle control to FAST (rabbit) position. 4. Move choke to the ON position (cold engine start). If 5. engine is warm, place choke in OFF position. Push primer three to five (3-5) times, making sure 6. to cover vent hole when pushing. If engine is warm, push primer only once. Always cover vent hole when pushing. Cool weather may require priming to be repeated. Push starter button to start engine. 7. Once the engine starts, immediately release starter button. Electric starter is equipped with thermal overload protection; system will temporarily shut-down to allow starter to cool if electric starter becomes overloaded. As the engine warms, slowly rotate the choke control 8. to OFF position. If the engine falters, restart engine and run with choke at half-choke position for a short period of time, and then slowly rotate the choke into OFF position. After engine is running, disconnect power cord from 9. electric starter. When disconnecting, always unplug the end at the wall outlet before unplugging the opposite end from the engine. Stopping the EngineWARNING: To avoid unsupervised engine operation, never leave the engine unattended while running. Turn the engine off after use and remove ignition key Run engine for a few minutes before stopping to help dry off any moisture on the engine. Move throttle control to STOP position. 1. Remove the ignition key. Removing the key will 2. reduce the possibility of unauthorized starting of the engine while equipment is not in use. Keep the key in a safe place. The engine cannot start without the ignition key. Wipe all snow and moisture from the area around the 3. engine as well as the area in and around the drive control and auger control. Also, engage and release both controls several times. WARNINGRead, understand, and follow all instructions and warnings on the machine and in this manual before operating. Use extreme care when handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Never fuel the machine indoors or while the engine is hot or running. Extinguish cigarettes, cigars, pipes and other sources of ignition. If your home’s wiring system is not a three-wire grounded system, do not use this electric starter under any conditions. If your home electrical system is grounded, but a three-hole receptacle is not available, do not use your snow thrower’s electric starter. 10 To Engage Drive 1. With the engine running near top speed, move shift lever to one of six FORWARD positions or two REVERSE positions. Select a speed appropriate for the snow conditions that exist. Do not shift speeds while the drive is engaged. 2. Squeeze drive control against the right handle and the snow thrower will move. Release it and the drive motion will stop. To Engage Augers 1. To engage augers and start snow throwing, squeeze the left hand auger control against the left handle. Release to stop augers. 2. While the auger control is engaged, squeeze the drive control to move, release to stop. Do not shift speeds while the drive is engaged. NOTE: This drive lever also locks auger control so you can turn the chute control without interrupting the snow throwing process. 3. Release the auger control; the interlock mechanism should keep the auger control engaged until the drive control is released. 4. Release the drive control to stop both the augers and the wheel drive. To stop the auger, both levers must be released. Auger Control Test Perform the following test before operating your snow thrower for the first time and at the start of each winter. Check the adjustment of the auger control as follows: 1. When the auger control is released and in the disengaged “up” position, the cable should have very little slack. It should NOT be tight. 2. In a well-ventilated area, start the snow thrower engine as instructed on the previous page. Make sure the throttle is set in the FAST position. 3. While standing in the operator’s position (behind the snow thrower), engage the auger. 4. Allow the auger to remain engaged for approximately ten (10) seconds before releasing the auger control. Repeat this several times. 5. With the auger control in the disengaged “up” posi- tion, walk to the front of the machine. When selecting a Drive Speed, use the slower speeds until you are comfortable and familiar with the operation of the snow thrower. NEVER reposition the shift lever (change speeds or direction ...