Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
3. Always refer to operator’s manual for important details if the snow thrower is to be stored for an extended period. 4. Maintain or replace safety and instruction labels, as necessary. 5. Run the machine a few minutes after throwing snow to prevent freeze-up of the collector/impeller. CONGRATULATIONS on your purchase of a new snow thrower. It has been designed, engineered and man u fac tured to give best possible dependability and per for mance. Should you experience any problem you cannot easily remedy, please contact your nearest authorized service center. We have competent, well-trained tech ni cians and the proper tools to service or repair this unit. Please read and retain this manual. The instructions will enable you to assemble and maintain your snow thrower prop er ly. Always observe the “SAFETY RULES”. SERIAL NUMBER: ___________________________ DATE OF PURCHASE: _______________________ THE MODEL AND SERIAL NUMBERS WILL BE FOUND ON A DECAL ATTACHED TO THE REAR OF THE SNOW THROWER HOUSING. YOU SHOULD RECORD BOTH SERIAL NUMBER AND DATE OF PURCHASE AND KEEP IN A SAFE PLACE FOR FUTURE REFERENCE. PRODUCT SPECIFICATIONS Gasoline Capacity and Type: 1.0 Quarts (1,9 Liters) Unleaded Regular only Oil Type (API SG–SL): SAE 5W-30 or 10W-30 Synthetic SAE 5W-30 Oil Capacity: 28 Ounces (0,83 Liters) Spark Plug: Gap: Champion QC12YC/692720 0.030" (0,762 mm) CUSTOMER RESPONSIBILITIES • Read and observe the safety rules. • Follow a regular schedule in maintaining, caring for and using your snow thrower. • Follow the instructions under “Maintenance” and “Storage” sec tions of this own er’s manual. TABLE OF CONTENTS SAFETY RULES ........................................................ 2-3 MAINTENANCE SCHEDULE ..................................... 14 PRODUCT SPECIFICATIONS ......................................3 SERVICE AND AD JUST MENTS ...........................16-18 CUSTOMER RESPONSIBILITIES ................................ 3 STORAGE ................................................................... 19 ASSEMBLY / PRE-OPERATION ............................... 4-7 TROU BLE SHOOT ING ................................................ 20 OPERATION ............................................................ 8-13 REPAIR PARTS ..................................................... 21-39 MAINTENANCE ..................................................... 14-15 WARRANTY ............................................... BACK PAGE 3 PARTS PACKED SEPARATELY IN CARTON (1) POWER CORD (198563) (1) AUGER CONTROL ROD SAFTEY IGNITION KEY(S) (193071) (1) FUEL STABILIZER PACKET (1) MULTI- WRENCH (180684) (1) DISCHARGE CHUTE (1) LOCKNUT 5/16-18 (751153) (1) CARRIAGE BOLT 5/16-18 x 5/8 (72250505) (1) LOCKNUT 1/4-20 (191730) (1) SHOULDER BOLT 1/4-20 (179829) (1) SPRING (184505) CHUTE DEFLECTOR REMOTE CONTROL EXTRA SHEAR BOLTS AND NUTS (2) SHOULDER BOLT 1/4-20 x 1-3/4 (192090) (1) WASHER 3/8 (19131316) (1) LOCKNUT 3/8 (73800600) (3) RETAINER SPRINGS (169675) (2) LOCKNUTS 1/4-20 (73800400) ROTATOR HEAD MOUNTING (2) FLAT WASHERS (2) CARRIAGE BOLTS 3/8-16 x 2.25 (2) HANDLE KNOBS ASSEMBLY / PRE-OPERATION Read these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower. Reading the entire manual will familiarize you with the unit, which will assist you in assembly, operation and maintenance of the product. Your new snow thrower has been as sem bled at the factory with the ex cep tion of those parts left unassembled for shipping purposes. All parts such as nuts, washers, bolts, etc., necessary to com plete the as sem bly have been placed in the parts bag. To ensure safe and proper operation of your snow thrower, all parts and hard ware you assemble must be tightened se cure ly. Use the correct tools as nec es sary to ensure proper tightness. 2. Cut down all four corners of carton and lay panels flat. 3. Remove the two (2) screws securing the auger housing to the pallet. 4. Remove all packing materials ex cept plastic tie holding speed control rod to lower handle. 5. Remove the two (2) plastic ties securing the upper handle to the pallet. 6. Remove snow thrower from carton and check carton thor ough ly for ad di tion al loose parts. HOW TO SET UP YOUR SNOW THROWER TOOL BOX (See Fig. 10) A toolbox is provided on your snow thrower. The toolbox is REMOVE SNOW THROWER FROM CAR TON located on top of the belt cover. Store the extra shear bolts, 1. Remove all accessible loose parts and parts boxes nuts and multi-wrench provided in parts bag in the toolbox. from carton. 4 5 ASSEMBLY / PRE-OPERATION NOTE: The multi-wrench may be used for assembly of the chute rotator head to snow thrower and making ad just ments to the skid plates. UNFOLD UPPER HANDLE 1. Raise upper handle to the operating position and tight en handle knobs securely. Additional carriage bolts, washers and handle knobs are in bag of parts. Use to secure upper handle to lower handle. Install in lower holes in handles. INSTALL SPEED CONTROL...
Эта инструкция также подходит к моделям:Снегоочистители - PP115E27 (2.97 mb)