Оценок - 9, средний балл: 3.9
(
)
)
|
Фото и характеристики Cub Cadet 524 SWE |
Фрагмент инструкции
Remove the frame cover from the underside of the snow thrower by removing four self-tapping screws which secure it. Refer to Fig. 8-3. 1. 2. 3. a. b. c. 4. 5. Figure 8-6 Figure 8-5 Section 78 — Service 21 Slip the drive belt off the pulley and between friction wheel and friction wheel disc. See Fig. 8-7. Remove and replace belt in the reverse order. NOTE: Engaging the drive control will ease reassembly of the belt. Friction Wheel Inspection If the snow thrower fails to drive with the drive control engaged, and performing the drive control cable adjustment fails to correct the problem, the friction wheel may need to be replaced. NOTE: Special tools are required and several components must be removed and in order to replace the snow thrower’s friction wheel rubber. See an authorized Service Dealer to have the friction wheel rubber replaced or phone Customer Support as instructed on page 2 for information on ordering a Service Manual. To inspect the friction wheel, proceed as follows: Place a piece of plastic under the gas cap and tighten securely. Carefully pivot the snow thrower up and forward so that it rests on the auger housing. 6. 7. 1. 2. Remove the frame cover from the underside of the snow thrower by removing four self-tapping screws which secure it. See Fig. 8-8. Examine the friction wheel for signs of wear or cracking. See Fig. 8-9. 3. 4. Figure 8-7 Figure 8-8 Figure 8-9 22 Section 78— S Problem Cause Remedy Engine fails to start Engine runs erratic Engine overheats Excessive vibration Loss of power Unit fails to propel itself Unit fails to discharge snow Choke control not in ON position. Spark plug wire disconnected. Fuel tank empty or stale fuel. Engine not primed. Faulty spark plug. Safety key not inserted . 1. 2. 3. 4. 5. 6. Engine running on CHOKE. Stale fuel. Water or dirt in fuel system. Carburetor out of adjustment. 1. 2. 3. 4. Carburetor not adjusted properly. 1. Loose parts or damaged auger. 1. Spark plug wire loose. Gas cap vent hole plugged. 1. 2. Drive control cable in need of adjustment. Drive belt loose or damaged. 1. 2. Chute assembly clogged. Foreign object lodged in auger. Auger control cable in need of adjustment. Auger belt loose or damaged. Shear pin(s) sheared. 1. 2. 3. 4. 5. 1. 2. 3. 4. 5. 6. 1. 2. 3. 4. 1. 1. 1. 2. 1. 2. 1. 2. 3. 4. 5. Move choke control to ON position. Connect wire to spark plug. Fill tank with clean, fresh gasoline. Prime engine as instructed in the Operation section. Clean, adjust gap, or replace spark plug. Insert key fully into the switch. Move choke control to OFF position. Fill tank with clean, fresh gasoline. Drain fuel tank. Refill with fresh fuel. Contact your Cub Cadet Dealer. Contact your Cub Cadet Dealer. Stop engine immediately and disconnect spark plug wire. Tighten all bolts and nuts. If vibration continues, have unit serviced by your Cub Cadet Dealer. Connect spark plug wire. Remove ice and snow from gas cap. Be certain vent hole is clear. Adjust drive control cable. Refer to Maintenance and Adjustments section. Replace drive belt. Refer to Service section Stop engine immediately and disconnect spark plug wire. Clean chute assembly and inside of auger housing with clean-out tool or a stick. Stop engine immediately and disconnect spark plug wire. Remove object from auger with clean-out tool or a stick. Adjust auger control cable. Refer to Assembly & Set-Up section. Replace auger belt refer to Service section. Replace shear pin(s). Unit fails to turn Steering cable loose or damaged. 1. 1. Have unit serviced by your Cub Cadet Dealer. Troubleshooting 8 Component Part Number and Description 929-0071 Extention Cord, 110V 954-04050 Auger Drive Belt 754-0367 Wheel Drive Belt 684-04159 Friction Wheel Assembly 935-04054 Friction Wheel Rubber 725-1629 Lamp, 12.8V 738-04124A Shear Pin, 1.50 714-04040 Bow-tie Cotter Pin 790-00091 Slide Shoe, Deluxe 731-2643 Chute Clean-out Tool 790-00120 Shave Plate, 24” 751-10630 Key 751-10292 Spark Plug Phone (800) 965-4CUB to order replacement parts or a complete Parts Manual (have your full model number and serial number ready). Parts Manual downloads are also available free of charge at Replacement Parts 9 24 Notes 10 Cub Cadet LLC (Cub Cadet), The United States Environment Protection Agency (U. S. EPA) Emission Control System Warranty Statement (Owner’s Defect Warranty Rights and Obligations) The U. S. EPA and Cub Cadet are pleased to explain the emissions control system warranty on your model year 2005 and later small off-road engine. New small off-road engines must be designed, built and equipped to meet the stringent anti-smog standards. Cub Cadet must warranty the emission control system on your engine for the period of time listed below, provided there has been no abuse, neglect or improper maintenance of your small off-road engine. Your emission control system may include parts such as the carburetor, air cleaner, ignition system, exhaust system, and other associated emission- related compone...