Оценок - 3, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
If all appear to be OK, plug the unit in again. If snow does not come out after holding the remote control button for 30 seconds, check the hose attached tothe tank to make sure there is fluid going through the hose. If you are unable to determine the cause of the problem, do not simply continue to push the remote control button as this may damage the unit. ContactCHAUVET for servicing. Contact Chauvet USA Tecnical Assistance: 1-800-762-1084 (954) 929-1115 E-Mail tech@chauvetlighting.com Caution • Never use any other type of liquid other than UNSCENTED water based snow fluid. • Use of any other fluids or additives will void the warranty • Do not obstruct the nozzle. • Never aim the nozzle directly at people or naked flames. • Keep out of reach of children. Do not leave machine unattended. • Never drink snow liquid. If its ingested, call a doctor immediately. If fluid comes into contact with skin or eyes, rinse thoroughly with water. • Beware of condensation on the floor from accumulation of snow. Consider carefully when using the SM-150X. Power Connections The unit is supplied with a power plug appropriate to its voltage and destination. Should any other connections be required they must be carried out with the following configuration. Earth = Green/Yellow cable Neutral = Blue cable Live = Brown cable In the USA & Europe, it is required that all plugs are 3-pin type i.e. with Earth/Ground connection. In the UK, it is required that all mains plugs are fitted with 5A fuses. Technical Specifications Power Input: AC 120V 60 Hz or 230V 50 Hz Snow Output: 10 Cubic inches per Minute Fuse: 15A 125V or 10A 250V Tank Capacity: 5 Liter Dim: 21.3 x 9.8 x 11.2 in 540 x 250 x 285mm Weight: 26.4 lbs / 12 Kg User Informtion (Please complete for your records) Date Purchased: / / Serial No: ________________ Dealer Stamp Model: SM-150X DMX Snow Machine DMX Snow Machine SM-150X User Guide Please read these instructions carefully before use World-wide Headquarters: 3000 North 29th Ct. Hollywood, Florida, USA 33020 Tel: +1-954-929-1115 Fax: +1-954-929-5560 On the Rear • Socket for Remote Control (In/Out) • Eyebolt for Safety Cable • DMX In/Out • Sock • Blower Lo/High • Manual Snow button • On/Off Switch • Power Cord Socket and Fuse holder Introduction Congratulations on the purchase of your new CHAUVET snow machine. We are confident you will enjoymany trouble free hours with this unit. To assist with the care and use of the product we have prepared this short guide. Operation Before connecting this unit to the mains power supply for the first time you must first fill the fluid tank with snow fluid. Place the machine on a level surface and loosen the cap of the fluid tank to fill with quality unscented water based snow fluid. We recommend use of CHAUVET snow fluid as it has been specially formulated for use with CHAUVET snow machines. Plug the remote control unit into the socket at the rear of unit. The snow machine is ready to work immediately. There is no need for the unit to preheat. This snow machine has been designed to function on a mains power supply of either 120V~60Hz or230V~50Hz and has been fitted with a suitable power plug for use with your local voltage. Check the label on the unit and the power plug for the correct voltage. Always monitor fluid level as running the machine with no fluid could cause permanent damage. As with most electrical equipment, it is advised that the effect be used in well ventilated areas taking carenot to obstruct the air vents. · Never use any other type of liquid other than UNSCENTED water based snow fluid. · Use of any other fluids or additives will void the warranty. Maintenance & Servicing Work on internal parts should be carried out by a qualified technician. Removal of any covers is considered a breach of warranty and will not be covered under any such agreement unless authorized first by CHAUVET Controlling the SM-150X 1. FC-4HS Timer remote - Plug the controller into the back of the SM-150X and press the red button tocontinually generating snow. Press the yellow button to activate the timer functions. Adjust the duration and interval knobs to achieve the desired effect. The unit will cycle regularly to the settings. Depress the yellowbutton again to exit time mode. To use the FC-4HS manually, simply depress and hold the green button togenerate the desired amount of snow. 2. DMX Mode - The SM-150X is a one channel unit that controls the volume of snow generated. To operatein DMX mode, you must link the units together using a premium quality 3-pin DMX cable in the following configuration. 'Out' from the first unit to 'In' on the second, 'Out' from the second to 'In' on the third and soon. Please consult the controller manual to determine the proper address for the units. Example: To set the address at 12 1.Set SW 10 to OFF. 2. Count the value of the switches in the on position. and SW 4 equals 8. 3. Set SW 3 and SW 4 to the ON position. (4 + 8 = 12) Off On Valu...