Оценок - 2, средний балл: 5
(
)
)
|
Фрагмент инструкции
For close snow removal on a smooth surface, raise skid shoes higher on the auger housing. Use a middle or lower position when the area to be cleared is uneven, such as a gravel driveway NOTE: If you choose to operate the snow thrower on a gravel surface, keep the skid shoes in position for maximum clearance between the ground and the shave plate. To adjust the skid shoes: Loosen the four hex nuts (two on each side) and carriage bolts. • • 1. Figure 7 CaUTion It is not recommended that you operate this snow thrower on gravel as it can easily pick up and throw loose gravel, causing personal injury or damage to the snow thrower and surrounding property. Move skid shoes to desired position. See Figure 7. 2. Make certain the entire bottom surface of skid shoe is against the ground to avoid uneven wear on the skid shoes. 3. Retighten nuts and bolts securely. 10 11 ASSEMBLY Chute Assembly The distance snow is thrown can be adjusted by changing the angle of the chute assembly. To do so: Stop the engine by removing the ignition key and loosen the plastic wing knob found on the left side of the chute assembly. Pivot the chute upward or downward before retightening the wing knob. See Figure 8. Auger Control Check the adjustment of the auger control as follows: When the auger control is released and in the disengaged “up” position, the cable should have very little slack. It should NOT be tight. In a well-ventilated area, start the snow thrower engine. Refer to Starting the Engine in the Operation section. Make sure the throttle is set in the FAST position. While standing in the operator’s position (behind the snow thrower), engage the auger. Allow the auger to remain engaged for approximately ten (10) seconds before releasing the auger control. Repeat this several times. With the throttle control in the FAST (rabbit) position and the auger control in the disengaged “up” position, walk to the front of the machine. Confirm that the auger has completely stopped rotating and shows NO signs of motion. If the auger shows ANY signs of rotating, immediately return to the operator’s position and shut off the engine. Wait for ALL moving parts to stop before re-adjusting the auger control. To readjust the control cable, loosen the upper hex nut on the auger cable bracket. See Figure 9. Position the bracket upward to provide more slack (or downward to increase cable tension). Retighten the upper hex nut. Repeat steps 2-6 above to verify proper adjustment has been achieved. 1. 2. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Figure 9 WARNING Prior to operating your snow thrower, carefully read and follow all instructions below. Perform all adjustments to verify your snow thrower is operating safely and properly. Figure 8 12 OPERATION Now that you have setup your snow thrower, it’s important to become acquainted with its controls and features. Refer to Figure 10. Shift Lever The shift lever is located on the dash panel. Place the shift lever into any of eight positions to control the direction of travel and ground speed. Forward Your snow thrower has six forward (F) speeds. Position one (1) is the slowest and position six (6) is the fastest. Reverse Your snow thrower has two reverse (R) speeds. One (1) is the slower and two (2) is the faster. Ignition Key The ignition key is a safety device. It must be fully inserted in order for the engine to start. Remove the ignition key when the snow thrower is not in use. NOTE: Do not turn the ignition key in an attempt to start the engine. Doing so may cause it to break. Choke Control The choke control is found on the rear of the engine and is activated by rotating the knob clockwise. Activating the choke control closes the choke plate on the carburetor and aids in starting the engine. Figure 10 Meets ANSI Safety Standards Craftsman Snow Throwers conform to the safety standard of the American National Standards Institute (ANSI). Drive Control Gas Cap Oil Fill Electric Start Button Chute Directional Control Chute Assembly Clean-Out Tool Auger Control Shift Lever Skid Shoe Augers Engine Controls Recoil Starter Handle Electric Starter Outlet Primer Ignition Key Choke Control Throttle Control OPERATION throttLe ControL The throttle control is located on the rear of the engine. It regulates the speed of the engine and will shut off the engine when moved into the STOP position. reCoiL StArter hAndLe This handle is used to manually start the engine. eLeCtriC StArter Button Pressing the electric starter button engages the engine’s electric starter when plugged into a 120V power source. eLeCtriC StArter outLet Requires the use of a three-prong outdoor extension cord (included) and a 120V power source/wall outlet. AugerS When engaged, the augers rotate and draw snow into the auger housing. Chute ASSeMBLy Snow drawn into the auger housing is discharged out the chute assembly. PriMer Depressing the primer forces fuel directly into the engine’s carburetor to aid in cold-weather starting. oiL fiLL Engine oil level can be...