Оценок - 4, средний балл: 3.8 ( )

Производитель: MTD Размер: 919.05 kb Название файла: Язык инструкции:

Turn on to run, turn off to stop. PRIMER: (Model 932001 only.) Push four times to prime engine with fuel prior to starting. STARTER BUTTON: The starter button (j[)is found on all units equipped with electric starters. Plug the 120 volt cord into the starter block; plug the opposite end into a convenient 120 volt outlet. Push the starter button to start the engine. CAUTION: A HIGH SPEED IMPELLER ROTATES INSIDE THIS HOUSING TO THROW THE SNOW. NEVER REACH OR PUSH ANY OBJECT INTO THE DISCHARGE CHUTE WITH THE IMPELLER RO- FIGURE 1 BEFORE STARTING Fill crankcase (jo) with Ariens Sno-Thro oil 5W-20 when using Sno-Thro. Use Ariens Gard-N-Yard oil MS classification SAE-30 oil when using lawn attachments. Refer to Engine Manual for appropriate crankcase oil substitutes. Fill fuel tank (1?) with fresh, clean, unleaded automotive gasoline. Do not mix oil with gasoline. (Leaded "regular" grade gasoline is an acceptable substitute). Make visual check with regards to safety precautions, obstructions, lubrication and maintenance. NOTE: Check for frozen fan before starting engine. These problems arise in wet, slushy snow. If the fan is frozen, it is best freed by thawing in a heated garage or other building. The best solution is preventing freezing. Allow the engine to run for a short time before shutting down to throw the remaining slush and water out of the blower housing and thus prevent freezing of the fan. After engine is stopped move choke lever to full choke and throttle control to fast and leave in this position. TO START Turn key (T) to "Run" position. Move choke lever (j[)to "FULL" choke position. Move throttle (¿) to "FAST" position. On Model 932001, push primer bulb four times. Pull recoil starter (l2) to start engine. If the machine is equipped with an electric starter attach the starter cable to the starter switch, plug the cable into any convenient 120 volt electrical outlet - and depress the starter button to crank and start the engine. Follow the starter manufacturers instructions supplied with the starter. Move choke to 3/4 choke, then to 1/2 choke, then to "OFF". TO TRANSPORT Move speed selector (T) to desired speed. Press down on handlebars to raise front of Sno-Thro slightly off the ground. Depress tractor clutch lever (T) to transport unit. TO OPERATE Move deflector (l?) to desired height. Turn hand crank (T) to direct discharge chute. Move throttle (Y) to "FAST" speed. Move speed selector (T)to desired speed. Depress attachment clutch (V) to in position. Depress tractor clutch lever (T) to move tractor. Note that the clutch lever on BOTH handelbars must be depressed to operate the machine and blow snow. Speed of the machine is controlled by the throttle and speed selector. TO STOP Release tractor Clutch lever (T). Allow the Sno-Thro to run for a short time to throw out slush and water and prevent freezing of the fan. Release attachment clutch (T). Turn key (7) to "Off" position. Place chjjke(6)in "FULL" choke position. Place throttle control (2y in "FAST" position. MAINTENANCE Ariens Company recommends that you have adjustments made by your local Ariens dealer. He has the tools and knowhow to properly perform these maintenance adjustments which may be required to keep the Sno-Thro operating at peak efficiency. The Sno-Thro is equipped with the finest quality engine obtainable. However, should servicing be required, it can be obtained from an Ariens dealer or an authorized engine manufacturer's service station. Should you decide to make adjustments on your Sno-Thro yourself, Ariens recommends that you call your dealer for the answers to any questions that might arise in performing this work. SHEAR BOLT REPLACEMENT Occasionally a small object may enter the collector and jam the rakes. When this occurs, the shear bolts securing the rakes to the shaft will break and allow the rake to turn freely on the shaft preventing damage to the gear drive. When this happens, turn off the engine, remove wire from spark plug, remove the broken shear bolt and replace with a new ARIENS shear bolt. Use of any other type of shear bolt may result in severe damage to the machine. USE ONLY ARIENS SHEAR BOLTS FOR REPLACEMENT. Each time a shear bolt is replaced (and once each year) the rake should be rotated on the shaft and the shaft oiled. Oil shaft through shear bolt holes. The runners (14) on each, side of the blower housing are all adjustable to suit conditions. Raising or lowering the runners controls the distance the scraper is held above the surface being cleared. Runners are adjusted by loosening the two nuts securing each runner. Move the runner to the desired position and retighten the nuts. Be sure to adjust both runners to the same height to keep blower housing level. Uneven runners make the machine difficult to steer and will result in an uneven clearing job. Adjustment of the runners is critical to good cleaning. If the machine is to be used on a gravel surface; lower the...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: