Оценок - 2, средний балл: 4 ( )

Производитель: MTD Размер: 8.57 mb Название файла: Язык инструкции:

Insert the hair pin with the loop end to the left of the chute rod so the control assembly follows a full range of travel. 9. Insert the chute lock cable fitting into the bracket on the chute pedestal, and then connect the chute lock cable to the lock teeth by fitting the cable ball end into the slot on the lock teeth. See Figure 11. NOTE: Press down on lock teeth with your finger to align the cable ball end with the slot (Figure 11). 10. Replace the gear cover removed in step 4. IMPORTANT: Rotate the discharge chute to the left when tightening the pedestal hardware to ensure clearance between the discharge chute and the belt cover. 11. Tighten pedestal hardware to 15 - 31 lbf-ft (20 - 42 N^m). 12. Make sure the discharge chute rotates left and right when you push the discharge chute control lever left and right. GB - 10 Install Discharge Chute and Discharge Chute Crank (921001) (Figure 12) 1. Grease underside of discharge chute ring (if not already greased). 2. Remove mounting hardware from auger housing. 3. Install discharge chute over opening in the auger housing. Finger tighten the mounting hardware removed in step 2. NOTE: Leave discharge chute pedestal loose to help install the chute rod and connect it to the control assembly. the hole in the front of the control panel. 5. Connect the chute crank to the pinion gear on chute with spring clip. IMPORTANT: Rotate the discharge chute to the left when tightening the pedestal hardware to ensure clearance between the discharge chute and the belt cover. 6. Tighten pedestal hardware to 15 - 31 lbf-ft (20 - 42 N^m). Deflector Remote (921002, 003, 004) Connect the cable end to the cable anchor on the discharge deflector before clipping the cable to the cable bracket on the discharge chute. 1. Route deflector remote cable along the left side of the chute pedestal. 2. Insert the barrel on the cable end into the bracket on left side of chute deflector (Figure 13). 3. Hold seal out of the way while routing the cable through the bracket on the left side of the discharge chute, and then push the cable fitting into the bracket. 4. Push the seal securely over the end of the cable fitting to prevent water from entering the cable. 5. Check deflector travel. Adjust nut on cable end under handlebar to obtain full travel, if necessary. (see Deflector Remote (921002, 003, 004) on page 25). 23 2. Cable End 3. Deflector Cable 4. Cable Fitting 5. Cable Bracket Figure 13 Check Function of Dual Handle Interlock Without the engine running, press down (engage) both clutch levers. Release attachment clutch lever. Attachment clutch should remain engaged until traction clutch lever is released, then both clutches must disengage. If they do not, contact your Dealer for repairs. GB - 11 Check Tire Pressure Check tire pressure and adjust to the pressure listed on tire sidewall. A CAUTION: Avoid injury! Explosive separation of tire and rim parts is possible when they are serviced incorrectly: • Do not attempt to mount a tire without the proper equipment and experience to perform the job. • Do not inflate the tires above the recommended pressure. • Do not weld or heat a wheel and tire assembly. Heat can cause an increase in air pressure resulting in an explosion. Welding can structurally weaken or deform the wheel. • Do not stand in front or over the tire assembly when inflating. Use a clip-on chuck and extension hose long enough to allow you to stand to one side. Check Auger Gearcase Oil Check oil level in auger gearcase (see Check Auger Gearcase on page 22). Check Engine Crankcase Oil IMPORTANT: The engine is shipped with 5W-30 oil in crankcase. Refer to Engine Manual for detailed instructions. Fill Engine Fuel Tank Refer to Engine Manual for proper fuel type and tank capacity. Check Function of all Controls Ensure unit runs and performs properly. Refer to OPERATION on page 15. Run-in Attachment Belt 1. Start unit in a well-ventilated area according to Starting and Shut Off on page 19. 2. Engage attachment clutch lever and run attachment for about 15 minutes. 3. Stop unit, wait for all moving parts to stop, and remove spark plug wire. 4. Adjust belt finger, if necessary. See Check Belt Finger Clearance on page 30. 5. Adjust clutch idler according to Attachment Clutch/Brake Adjustment on page 27. GB - 12 CONTROLS and FEATURES 1. Attachment Clutch Lever 2. Speed Selector 3. Traction Drive Clutch Lever 4. Chute Control 5. Oil Fill/Dipstick 6. Discharge Chute Deflector 7. Discharge Chute 8. Impeller 9. Clean-Out Tool 10. Auger 11. Scraper Blade 12. Auger Gearcase 13. Recoil Starter Handle 14. Electric Starter 15. Wing Knobs 16. Ignition Key, Push-Pull 17. Oil Drain Plug 18. Throttle (Engine Stop) 19. Choke Control Knob 20. Primer Bulb 21. Runner 22. Axle Lock Pin 23. Belt Cover 24. Fuel Shut-Off Valve 25. Fuel Tank and Cap GB - 13 1. Attachment Clutch Lever 2. Speed Selector 3. Deflector Remote Control 4. Chu...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: