Оценок - 3, средний балл: 5
(
)
)
|
Фрагмент инструкции
• Slide the rubber dust cover (F) over the plastic fitting (B). 2 3 8 Figure 7 TP 1000-4518-01-LW-S Form No. 173xxxx-00 Two-Stage Snowthrower 1694986 10530L, 10.5 Snowthrower B A A C D B D Figure 3 A B C A B C D A B D E C D B A A B Remove Snowthrower From Crate • Cut the two zip ties from between wheels and the wood pallet. • Remove screws (A, Figure 11) from both skid shoes (B). • Roll snowthrower off crate. Add Oil and Fuel Note: Engine is NOT shipped with oil. Add 5W-30 premium engine oil. See Engine Manual for complete engine oil specifications and maintenance. • Clean the area around the oil fill tube (A, Figure 12). Remove the dip stick (B) from the oil fill tube and wipe the dip stick with a clean rag. • Insert the dip stick (B) into the oil fill tube (thread in or push down completely). • Remove and check the engine oil level (C). Oil level should be between FULL and ADD MARKS. If necessary, add oil to the oil fill tube. • Replace and fully secure the dip stick (B). • Remove the fuel cap (D, Figure 12). • Add clean, fresh, UNLEADED fuel with a minimum of 87 octane, leaving one inch of space from the top of the tank for fuel expansion. • Reinstall the fuel cap (D). Final Checks • Reduce the tire pressures to the pressures shown below. Tires are over-inflated for shipping purposes and must be set to the correct pressures for optimum performance. Tire Pressure: 14 PSI • Check control lever cables (A, Figure 13). Check the “Z” bend ends (C) of the control cables (A) are secured in the holes on the control levers (B) as shown. Check that the cables (A) are not kinked and have freedom of movement. Check that the auger cable, right side, (A, Figure 13) is on top of cable button (D) as show. • Loosely secure the spout rotator brake cable to the spout rotator rod with a zip tie. • To prevent the chute deflector cable from contacting the tire, rotate the chute all the way to the left and secure cable to the left handle with zip tie (see Figure 1). • Adjust light and secure the light wire to the handle with a zip tie. Starting the Engine • Turn the fuel valve (B, Figure 14) to the ON position. • Insert the engine key (F) into the engine key slot and push in fully. • Move the throttle lever (E) all the way to the right, to the FAST position. • Turn the choke knob (G) fully counter clockwise if engine is cold. (Do not choke a warm engine.) • Push the primer button (D) two times if engine is cold. (Do not prime a warm engine.) • Engine Mounted Electric Start: See Operator’s Manual. • Manual Start: Pull starter handle (C) rapidly to start the engine. Do not allow the starter handle to snap back—let the starter rope rewind slowly—while keeping a firm grip on the starter handle. • As the engine starts and begins to operate evenly, turn the choke knob (G) slowly clockwise to the RUN position, and set the Throttle Lever to SLOW. If the engine falters, turn the choke knob counter-clockwise until the engine runs smoothly, and let it run briefly before returning the choke to the RUN position. NOTE: Allow the engine to warm up at SLOW throttle for a few minutes before operating the snowthrower at full speed. The engine will not develop full power until it reaches operating temperature. After warming up, always operate at full throttle. Check that Clean-Out Tool is attached to Snowthrower • Always use a clean-out tool to clear clogged discharge chute. Never use use your hands. Snowthrower and Adjustments • Read Operator’s Manual. 9 A C B D 10 Figure 10 Figure 5 Figure 6 B C 7 Figure 8 Figure 9 D A E C E D B C B C G A B A B Figure 11 Figure 12 C D Figure 13 D B D C B A Figure 14 11 12 13 E E C Figure 1 14 A A C B Oil Dip Stick Clean-Out Tool Head Light Speed Selector Chute Deflector Control Auger Engage Control Traction Engage Control Fuel Cap Easy Turn Lever Chute Rotator Control Drift Cutter Skid Shoe Drift Cutter C D F B E G A E Remove the Packaging Materials • Remove the straps or banding and cardboard from the crate. Remove the parts bag (A, Figure 2) from inside the chute (B). Locate and remove the manual packet (C). 1 A B C Cut Along Line Cut Along Line 4 5 6 D D Chute Deflector Cable E D E TP 1000-4518-03-LW-SN:Q...
Эта инструкция также подходит к моделям:Снегоочистители - 10.5 (2.01 mb)