Оценок - 2, средний балл: 5 ( )

Производитель: Simplicity Manufacturing Размер: 651.62 kb Название файла: a443dad1-c2e4-b134-3196-6d6d80e57c4d.pdf Язык инструкции:

• Always wear substantial footwear and appropriate winter clothing. Wear foot-ware that improves traction on slippery slopes. DO NOT wear long scarves or loose clothing that could become entangled in moving parts. • Before using, always visually check that all hardware is present, in-tact, and secure. Replace worn or damaged parts. • Never operate the machine with defective guards, or without safety protective devises in place. • Stop engine before: refuelling, removing an attachment, making adjustments (unless the adjustment can be made from the operator’s position). • Follow the manufacturer’s recommendation for wheel weights or counterweights. • Adjust skid shoe height to clear gravel or crushed rock surfaces. • Do not touch snowthrower parts which may be hot from operation. Allow such parts to cool before attempting to service the unit. CLEARING A CLOGGED DISCHARGE CHUTE Hand contact with the rotating impeller inside the discharge chute is the most common cause of injury associated with snowthrowers. Always use a clean-out tool, not your hands. to clean out the discharge chute. To clear the chute: 1. SHUT OFF THE ENGINE. 2. Wait 10 seconds to be sure the impeller blades have stopped rotating. 3. Always use a clean out tool, not your hands. WARNING Gasoline is highly flammable and must be handled with care. Never fill the tank when the engine is still hot from recent operation. Do not allow open flame, smoking or matches in the area. Avoid over-filling and wipe up any spills. Do • See your authorized dealer for recommendations counterweights to improve stability. • Travel up and down slopes, not across. • Remove obstacles such as rocks, tree limbs, etc. • Watch for holes, ruts, or bumps. Uneven terrain could overturn the unit. Snow can hide obstacles. • Use slow speed. Tires may lose traction on slopes. Choose a low gear so that you will not have to stop or shift while on the slope. • Keep all movement on the slopes slow and gradual. Do not make sudden changes in speed or direction. • Always keep unit in gear especially when traveling downhill. Do Not • Do not start or stop on a slope. If tires lose traction, disengage the auger and proceed slowly straight down the slope. • Do not turn on slopes unless necessary, and then, turn slowly and gradually downhill, if possible. • Do not operate near drop-offs, ditches, or embankments. The unit could suddenly turn over if a wheel is over the edge of a cliff or ditch, or if an edge caves in. • Do not operate on wet surfaces. Reduced traction could cause sliding. • Do not shift to neutral and coast down hills. EMISSIONS • Engine exhaust from this product contains chemicals known, in certain quantities, to cause cancer, birth defects, or other reproductive harm. • Look for the relevant Emissions Durability Period and Air Index information on the engine emissions label. TP 300-5196-00-IS-SN 2 6/2006 Intermediate Frame Snowthrowers Quick Setup List Page Setup Procedure Steps to Perform Uncrating 4 Reduce Tire Pressures . Reduce Tire Pressure to 20 psi (137 kPa) & Check 4 Assembly . Install Drift Cutters 5 Assembly . Un-Folding Handles . Connecting Shift Rods 6 Assembly . Spout Rotator . Control Levers . Clean-Out Tool 7 Check Fluid Levels & Fill . Auger Gearcase . Engine Crankcase . Fuel Tank 7 Lubricate Snowthrower . Lubricate all grease & oil points 8 Lubricate Snowthrower . Lubricate the auger Shaft & Assembly Perform Safety Checks Functional Checks . Check that all Safety Guards are in place. . Check Scraper Bars & Skid Shoe Height . Check Drive Control & Auger Control . Check Chute Direction Control . Check Chute Deflector Control . Check Speed Selector Control Operational Checks . Start Engine & Test ALL Controls . Test Auger Stopping Time (Auger MUSTstop within 5 seconds after the control is released.) . Test Drive Controls . Check For Fluid Leaks 6/2006 3 TP 300-5196-00-IS-SN Intermediate Frame Snowthrowers Uncrating 1. Using a reciprocating saw, cut crate sides from bottom skid. Lift crate from bottom skid. 2. Remove screws securing skid shoes to bottom skid. Roll snowthrower from bottom skid backwards. 3. Make sure klik-pin is inserted through hole in wheel and axle shaft and secured. A Figure 1. Klik-pin-locked A. Klik-Pin Figure 2. Checking Tire Pressure Size PSI bar 15 x 5.0-6 20 1,38 4.80-8 20 1,38 Assembly Install Drift Cutters Drift cutters (if equipped) are mounted to snowthrower auger housing backwards or shipped loose. Refer to Figure 3. Remove hardware and install drift cutters with hardware as shown. B F H G Figure 3. Assemble Drift Cutters A. Taptite Screw, E Round Hole 5/16-18 x 3/4 F. Nut, 5/16-18 B. Drift Cutter G. Lockwasher, 5/16-18 C. TabH. Capscrew, D. Square Hole5/16-18 x 3/4 TP 300-5196-00-IS-SN 4 6/2006 Intermediate Frame Snowthrowers Assembly Un-Folding Handles Folding handles (if equipped) are shipped ...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: