Войти:
Оценок - 3, средний балл: 4.7 ( )

Инструкция по эксплуатации Craftsman, модель 1692986

Производитель: Craftsman
Размер: 1.74 mb
Название файла:
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


1. Remove the Engine Key from the switch. 2. Remove the fours screws securing the belt cover (see Figure 7). 3. Remove the cover. 4. Perform lubrication (see below). 5. Reinstall belt cover (reverse steps 3 to 1 above.) Figure 7. Removing Belt Cover Figure 9. Lightly oil pivot point LUBRICATION Note: The drive pulley end of auger shaft is supported by a sealed ball bearing and requires no lubrication. The ball bearing on other end of auger shaft is also sealed, and will not require lubrication. Lightly Oil • A few drops of oil should be placed on wheel hubs occasionally to keep wheels turning freely. • Apply oil to pivot points of auger control periodically, wiping off any excess oil. • A couple of drops of light machine oil applied to upper end of auger control cable will assure free movement of cable through outside casing. Wipe off any excess oil. • Remove belt cover and lightly apply oil to the pivot point for idler pulley arm. BE CAREFUL NOT TO GET OIL ON BELT OR PULLEYS. Grease • At the beginning of each snow throwing season, remove discharge chute and generously lubricate steel flange at back of rotating ring with light grease. Rotate ring with crank to distribute grease. Engine Lubrication The two cycle engine used in this snow thrower is lubricated by the fuel and oil mixture. Observe recommended fuel to oil mixture ratio shown on page 9. Figure 8. Lubrication points Pivot Point Screws TROUBLESHOOTING Problem Possible Cause Remedy Engine fails to start 1. Key is OFF 1. Turn Key to the ON position 2. Failure to prime cold engine 2. Press primer button twice and restart. 3. Out of fuel 3. Fill fuel tank 4. Choke OFF - cold engine 4. Turn Choke to ON. 5. Engine flooded 5. Turn Choke to OFF; try starting 6. Spark Plug not sparking 6. Check Gap. Gap plug, clean electrode, or replace as necessary 7. Water in fuel, or old fuel 7. Drain tank (Dispose of fuel at an authorized waste facility). Fill with fresh fuel mixture. Engine starts hard or runs poorly 1. Fuel mixture too rich 1. Move choke to OFF position 2. Spark plug faulty, fouled, 2. Clean and gap, or replace or gapped incorrectly 3. Water in fuel, or old fuel 3. Drain tank (Dispose of fuel at an authorized waste facility). Fill with fresh fuel mixture. 4. Gas cap vent hole plugged 4. Clean vent hole or replace cap Unit does not throw snow 1. Loose or broken drive belt 1. Adjust or replace belt 2. Incorrect control cable 2. Adjust Auger Control cable adjustment 3. Discharge chute clogged, 3. Stop engine, remove key and foreign object lodged in auger clean out discharge chute 4. Broken control cable 4. Replace cable Auger does not stop turning 1. Incorrect control cable 1. Adjust Auger Control cable when control is released adjustment Excessive vibration 1. Loose parts or damaged 1. STOP engine and REMOVE the key, auger tighten all hardware. If vibration continues, see your dealer. Note: For repairs beyond the minor adjustments listed above, please contact your local Simplicity dealer. Fig...

Эта инструкция также подходит к моделям:
Снегоочистители - 1692917 (1.74 mb)
Снегоочистители - 1692918 (1.74 mb)
Снегоочистители - 1692977 (1.74 mb)
Снегоочистители - 1692978 (1.74 mb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории