Оценок - , средний балл:
(
)
)
Производитель: McCulloch
Размер: 3.03 mb
Название файла:
Язык инструкции:
Документ загружается, подождите пожалуйста
 |
Документ загружается, подождите пожалуйста
Фрагмент инструкции
Damage to the snow thrower can result. • Slower speeds are for heavier snow and faster speeds are for light snow and transporting the snow thrower. It is recommended that you use a slower speed until you are familiar with the operation of the snow thrower. NOTE: When both traction drive and auger control levers are engaged, the traction drive control lever will lock the auger control lever in the engaged position. This will allow you to release your right hand from the handle and adjust the discharge chute direction without interrupting the snow throwing process. TRACTION DRIVE DRIVE SPEED CONTROL LEVER CONTROL LEVER FIG. 16 CLEAN-OUT TOOL FIG. 14 MOUNTING CLIP DISCHARGE CHUTE 10 11 TO ADJUST SKID PLATES (See Fig. 16) NOTE: The wrench provided in your parts bag may be used to adjust the skid plates. Skid plates are located on each side of the auger housing and adjust the clearance between the scraper bar and the ground surface. Adjust skid plates evenly to proper height for current surface conditions. For removal of snow in normal con di tions, such as a paved driveway or side walk, place skid plates in the highest position (lowest scraper clear ance) to give a 1/8" clearance between the scraper bar and the ground. Use a middle position if the surface to be cleared is uneven. NOTE: It is not recommended to operate the snow thrower over gravel or rocky surfaces. Objects such as gravel, rocks or other debris, can easily be picked up and thrown by the impeller, which can cause serious personal injury, property dam age or damage to the snow thrower. • If snow thrower must be operated over gravel surface, use extra caution and be sure skid plates are adjusted to lowest (highest scraper clear ance) position. 1. Shut off engine and wait for all moving parts to stop. 2. Adjust skid plates by loosening the hex nuts, then moving skid plate to desired position. Be sure both plates are adjusted evenly. Tighten securely. OPERATION WARNING: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame. CAUTION: Alcohol blended fuels (called gas ohol or using ethanol or methanol) can attract moisture which leads to separation and for mation of acids dur ing storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied be fore stor age of 30 days or longer. Empty the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage In struc tions for ad di tion al information. Never use engine or car bu re tor cleaner products in the fuel tank or per ma nent damage may occur. SCRAPER BAR (See Fig. 16) The scraper bar is not adjustable, but is reversible. After con sid er able use it may become worn. When it has worn almost to the edge of the housing, it can be reversed, providing additional service before requiring replacement. Replace a dam aged or worn scrap er bar. BEFORE STARTING THE ENGINE CHECK ENGINE OIL LEVEL (See Fig. 17) The engine on your snow thrower has been shipped from the factory already filled with oil. 1. Check engine oil with snow thrower on level ground. 2. Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill. • To change engine oil, see “TO CHANGE ENGINE OIL” in the Main te nance sec tion of this manual. SKID PLATE LOW POSITION (HIGH GROUND CLEAR ANCE) HEX NUTS HIGH POSITION (LOW GROUND CLEARANCE) AUGER HOUSING FIG. 16 SCRAPER BAR ADD GASOLINE (See Fig. 17) • Fill fuel tank to bottom of tank filler neck. Do not overfill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. Do not mix oil with gasoline. Purchase fuel in quan ti ties that can be used within 30 days to assure fuel freshness. FIG. 21 PRIM ER SAFETY IG NI TION KEY ON / OFF SWITCH CHOKE CONTROL STARTER BUTTON FUEL SHUT-OFF VALVE NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION. ACTUAL LOCATION MAY VARY WITH ENGINE ON YOUR UNIT. POWER CORD PLUG GAS O LINE FILLER CAP ENGINE OIL FILL CAP / DIPSTICK RECOIL (AUXILIARY) STARTER HANDLE OPERATION TO START ENGINE • Be sure fuel shut-off valve is in the “OPEN” position. Your snow thrower engine is equipped with both a 120 Volt A.C. electric starter and a recoil starter. The electric starter is equipped with a three-wire power cord and plug and is designed to operate on 120 Volt A.C. household current. • Be sure your house is a 120 Volt A.C. three-wire ground ed system. If you are uncertain, consult a li censed electrician. WARNING: Do not use the electric start er if your house is not a 120 Volt A.C. three-wire grounded system. Se rious per son al injury or damage to your snow thrower could result. COLD START - ELECTRIC STARTER 1. Insert safety ignition key (tied to recoil start cord) into ignition slot until it clicks. DO NOT turn the key. Keep the extra s...
Эта инструкция также подходит к моделям:Снегоочистители - 96192004100 (3.03 mb)