Оценок - 4, средний балл: 3.5 ( )

Производитель: Ariens Размер: 7.4 mb Название файла: Язык инструкции:

OS7156 4 4 Figure 8 OS7270 Figure 9 1.Cable Anchor 2.Cable End 3.Deflector Cable 4.Cable Fitting 5.Cable Bracket 1 2 3 5 4 3 OS7070 Connect Battery (926500, 501) 1. Remove wing nuts from battery cover. 2. Install wire lead to battery terminal. 3. Install battery cover and tighten wing nuts. Check Function of Dual Handle Interlock Without the engine running, press down (engage) both clutch levers. Release attachment clutch lever. Attachment clutch should remain engaged until traction clutch lever is released, then both clutches must disengage. If they do not, contact your dealer for repairs. Check Tire Pressure Check tire pressure and adjust to the pressure listed on tire sidewall. Check Auger Gearcase Oil Check oil level in auger gearcase (see Check Auger Gearcase on page 20). Check Engine Crankcase Oil IMPORTANT: The engine is shipped with 5W-30 oil in crankcase. Refer to Engine Manual for detailed instructions. Fill Engine Fuel Tank Refer to Engine Manual for proper fuel type and tank capacity. Check Function of all Controls Ensure unit runs and performs properly. Refer to Operation. Run-in Attachment Belt 1. Start unit in a well-ventilated area according to Starting and Shut Off on page 17. 2. Engage attachment clutch lever and run attachment for about 15 minutes. 3. Stop unit, wait for all moving parts to stop, and remove spark plug wire. 4. Adjust belt finger, if necessary. See Attachment Drive Belt Replacement on page 27. 5. Adjust clutch idler according to Attachment Clutch/Brake Adjustment on page 25. GB - 12 GB - 13 1. Attachment Clutch Lever 2. Speed Selector 3. Deflector Remote Control 4. Chute Control 5. Traction Drive Clutch Lever 6. Oil Fill/Dipstick 7. Muffler Guard 8. Discharge Chute Deflector 9. Discharge Chute 10. Impeller 11. Clean-Out Tool 12. Auger 13. Scraper Blade 14. Auger Gearcase 15. Recoil Starter Handle 16. Electric Starter (926001, 002, 003, 004, 005, 006, 101, 102, 103, 300, 301, 302, 303, 304, 504) 17. Wing Knobs 18. Heated Handles 19. Ignition Key (926500, 501) 20. Remote Differential Wheel Lock (926001, 002, 003, 004, 005, 006, 300, 301, 302, 303, 304) 21. Heated Handles Switch 22. Oil Drain Plug 23. Throttle (Engine Stop) 24. Ignition Key, push-pull (926001, 002, 003, 004, 005, 006, 101, 102, 103, 300, 301, 302, 303, 304, 504, 505) 25. Choke Control Knob 26. Primer Bulb 27. Runner 28. Drift Cutter 29. Battery Cover and Battery (926500, 501) 30. Axle Lock Pin (926001, 101, 504, 505) 31. Belt Cover 32. Solenoid Compartment (926500, 501) 33. Fuel Shut-Off Valve 34. Fuel Tank and Cap 35. Headlight CONTROLS AND FEATURES Figure 10 1 2 3 4 5 6 7 8 9 10 11 12 13 14 17 1 18 19 20 18 5 4 21 3 2 22 23 24 25 26 15 28 27 29 31 32 33 34 35 30 16 OS7075 OS7080 OS7090 OPERATION OPERATION WARNING: AVOID INJURY. Read and understand the entire Safety section before proceeding. WARNING: To avoid injury to hands and feet, always disengage clutches, shut off engine, and wait for all movement to stop before unclogging or working on snow thrower. Keep hands and feet away from auger and impeller. CONTROLS AND FEATURES See Figure 10 for all Controls and Features locations. Dual Handle Interlock When Attachment Clutch and then Traction Drive Clutch are engaged, the Attachment Clutch will remain engaged (lever down) if released. To stop attachment, release Traction Drive Clutch and both clutches will disengage. Traction Drive Clutch - Left Hand Lever 1 2 OL2701 Squeeze the Traction Drive Clutch Lever against the Handlebar (1) to engage wheel drive for propelling unit. Forward speed will vary according to snow depth and moisture content. Release lever (2) to stop movement. NOTE: When traveling to or from the area to be cleared, press down on the handlebars enough to raise the front of the unit slightly off the surface. Engage the traction drive clutch without engaging the attachment drive clutch. Attachment Clutch - Right Hand Lever Squeeze Attachment Clutch Lever 2 against handlebar (1) to engage attachment. Release both clutch levers (2) to disengage power and apply brake to attachment. 1 IMPORTANT: If the belt squeals when the attachment clutch lever is OL2691 engaged, the impeller may be frozen in the auger housing. Immediately release the attachment clutch lever and move the unit into a heated area to thaw. NOTE: If belt squeals when impeller turns freely, see Attachment Drive Belt Replacement on page 27. Ignition Switch 2 Key Switch has two positions: 1. “Stop” - pulled out 2 2. "Run" - pushed in NOTE: DO NOT twist key after it is 1 inserted. OS1431 Ignition Switch (12V start on dash panel) The ignition switch is operated by a 2 31 removable key. It has three positions: 1.Stop 2.Run OS0232 3.Start Primer Bulb Pushing the primer bulb in adds fuel for easier engine start. Refer to Starting and Shut Off on page 17. OS1321 Speed Selector Position the Speed Selector in the appropriate speed notch to control forward and reverse travel. Forward: 6 1 1 2 (6) Fastest (1) Slowest Reverse: (1) Slow (2) Fast...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: