Войти:
Оценок - 3, средний балл: 4.3 ( )

Инструкция по эксплуатации Briggs & Stratton, модель 1738

Производитель: Briggs & Stratton
Размер: 1.36 mb
Название файла:
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


WARNING Gasoline and its vapors are extremely flammable and explosive. Fire or explosion can cause severe burns or death. When starting the engine, ensure that spark plug, muffler, fuel cap and air cleaner are in place and secured. Do not crank engine with spark plug removed. If engine floods, set choke (if equipped) to open/run position. WARNING Engines give off carbon monoxide, an odorless, colorless, poison gas. Breathing carbon monoxide can cause nausea, fainting or death. When starting the engine, start and run engine outdoors. Do not start or run engine in enclosed area, even if doors or windows are open. WARNING Unintentional sparking can result in fire or electric shock. Unintentional start-up can result in entanglement, traumatic amputation, or laceration. • Use a 3-wire extension cord. • First attach extension cord to electric starter connector and then into a wall receptacle. If additional extension cord is required, use a 3wire. • If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard. CAUTION This engine was shipped from Briggs & Stratton without oil. Before you start the engine, make sure you add oil according to the instructions in the Engine Owner’s Manual. If you start the engine without oil, it will be damaged beyond repair and will not be covered under warranty. 1. Check the oil level. See “How To Check/Add Oil” section in Engine Owner’s Manual. 2. Make sure equipment drive controls, if equipped, are disengaged. See the equipment manual for location and operation of these controls. 3. Move the throttle control lever (A, Figure 2) to the FAST position. Operate the engine with the throttle control lever in the FAST position. D C E B F A Figure 2. Start/Stop Engine - Manual A. Throttle Control Lever B. Fuel Shut-Off Valve C. Safety Key D. Choke Control Knob E. Primer Button F. Starter Cord Handle 14 Operation 4. Turn the fuel shut-off valve (B, Figure 2), if equipped, to the ON position. 5. Push in the safety key (C). 6. Turn the choke control knob (D) to the choke position. NOTE: Do not use the choke to start a warm engine. 7. Push the primer button (E) two times. NOTE: Do not use the primer to start a warm engine. 8. Rewind Start: Firmly hold the starter cord handle (F). Pull the starter cord slowly until resistance is felt, then pull rapidly. NOTE: If the engine does not start after three attempts, see the “Troubleshooting” section in the Engine Owner’s Manual. 9. Electric Start: First connect the extension cord to the power cord receptacle (A, Figure 3) and then into a wall receptacle. If an additional extension cord is required, make sure it is a 3-wire. WARNING If the extension cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard. CAUTION To extend the life of the starter, use short starting cycles (five seconds maximum). Wait one minute between starting cycles. 10. Electric Start: Depress the push button (B). After you start the engine, first disconnect the exten- sion cord from the wall receptacle and then from the power cord receptacle (A). NOTE: If the engine does not start after three attempts, see the “Troubleshooting” section in the Engine Owner’s Manual. 11. Allow the engine to warm up for several minutes. Then slowly move the choke control knob to the run position. B AC Figure 3. Start Engine - Electric A. Power Cord Receptacle B. Push Button C. Starter Cord Handle STOPPING THE ENGINE WARNING Gasoline and its vapors are extremely flammable and explosive.Fire or explosion can cause severe burns or death. Do not choke the carburetor to stop the engine. 1. Move the throttle control lever (A, Figure 2 ) to SLOW and then to the STOP position. 2. Remove the safety key (C). Keep the safety key out of the reach of children. 3. After the engine stops, turn the fuel shut-off valve (B) to the CLOSED position. 15 Operation OPERATING THE SNOWTHROWER 1. Rotate the discharge chute to the desired direction. 2. Set the speed selector to the desired forward speed. 3. Fully press and hold the auger engage control (C, Figure 4) on the right-hand grip to begin auger rotation. Releasing the auger engage control will disengage the auger — unless the Free-Hand™ Control has been activated (See step 5 below). 4. Fully press and hold the traction & Free-Hand™ Control lever (B, Figure 4) on the left-hand grip to engage the traction drive and begin moving the snowthrower. To disengage the traction drive, completely release the lever. 5. When BOTH levers are depressed, the Free-Hand™ Control is activated. This allows Auger Engage Control to be released — YET AUGER ROTATION WILL CONTINUE — until the Free-Hand™ Control is released. 6. Select forward or reverse speeds as needed using the Speed Selector (A, Figure 4). Release both control levers before changing drive speeds. CLEARING A CLOGGED DISCHARGE CHUTE IMPORTANT NOTE Hand cont...

Эта инструкция также подходит к моделям:
Снегоочистители - 1628 (1.36 mb)
Снегоочистители - 1732 (1.36 mb)
Снегоочистители - 1524 (1.36 mb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории