Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
Ignition Switch (Push /Pull) 18. Engine Shutoff Switch 19. Choke 20. Axle Lock Pin 21. Skid Shoe(s) 22. Belt Cover 23. Fuel Shut-off Valve 24. Handlebar CONTROLS AND FEATURES Figure 7 1 2 3 4 5 6 7 8 9 10 11 12 22 21 20 13 14 15 24 16 19 17 23 18 15 OPERATION OPERATION IMPORTANT: If the belt squeals when the attachment clutch lever is engaged, the impeller may be frozen in the auger housing. Immediately release the attachment clutch lever and move the unit into a heated area to thaw. NOTE: If belt squeals when impeller turns freely, see Attachment Drive Belt Replacement on page 20. Ignition Switch (Push/Pull Safety Key) Key Switch has two positions: WARNING: To avoid injury to hands and feet, always disengage clutches, shut off engine, and wait for all movement to stop before unclogging or working on snow thrower. Keep hands and feet away from auger and impeller. CONTROLS AND FEATURES See Figure 7 for all Controls and Features locations. Dual Handle Interlock When attachment clutch and then traction drive clutch are engaged, the attachment clutch will remain engaged (lever down) if released. To stop attachment, release traction drive clutch and both clutches will disengage. Traction Drive Clutch - Left Hand Lever 1 2 OL2701 Squeeze the traction drive clutch lever against the handlebar (1) to engage wheel drive for propelling unit. Forward speed will vary according to snow depth and moisture content. Release lever (2) to stop movement. NOTE: When traveling to or from the area to be cleared, press down on the handlebars enough to raise the front of the unit slightly off the surface. Engage the traction drive clutch without engaging the attachment drive clutch. Attachment Clutch - Right Hand Lever Squeeze attachment clutch lever against handlebar (1) to engage attachment. Release both clutch levers (2) to disengage power and apply brake to attachment. 2 1 OL2691 1. “Stop” - pulled out 2. "Run" - pushed in NOTE: DO NOT twist key after it is inserted. 2 1 Engine Shutoff Switch 1. Set the engine shutoff switch to the run position ("Run") to start and operate the engine. 2. Set the engine shutoff switch to the stop position ("Stop") to shut off a running engine. Primer Bulb Pushing the primer bulb in adds fuel for easier engine start. Refer to Starting and Shut Off on page 15. Speed Selector Position the speed selector in the appropriate speed notch to control forward and reverse travel. OS8225 1 26 1 GB - 12 GB - 13 Forward: (6) Fastest (1) Slowest Reverse: (1) Slow (2) Fast IMPORTANT: DO NOT change motion from forward to reverse with clutch engaged. Forward speed can be changed without declutching. Fuel Shut-Off Valve IMPORTANT: The fuel shut-off valve MUST be in the closed position prior to transporting the unit. The fuel shut-off valve has two positions: Choke Control 1. Choke Closed position: chokes off air to engine for easier start. 2. Choke Open position: allows for normal operation. IMPORTANT: Gradually open choke after engine starts. Recoil Starter Handle When pulled, handle will turn engine over. IMPORTANT: DO NOT let handle snap back against starter. See Starting and Shut Off on page 15. Snow Clean-Out Tool (Figure 9) To clear the discharge chute: 1. Shut off the engine. 2. Wait 10 seconds and make sure impeller blades have stopped rotating. 3. Remove the snow clean-out tool (1) from the auger housing and use it to remove the clog from the discharge chute. 4. Replace the snow clean-out tool on the auger housing. Discharge Chute Deflector ALWAYS position discharge chute deflector at a safe angle before starting engine. DO NOT throw snow any higher than necessary. Push deflector handle forward or down to throw snow lower. Pull deflector handle up or to the rear to throw snow higher. IMPORTANT: If chute deflector does not stay in set position, adjust as directed in SERVICE AND ADJUSTMENTS on page 18, or repair before operation. Discharge Chute Discharge chute rotates 205°. ALWAYS position discharge chute in safe direction and angle, away from operator and bystanders, before starting engine. Figure 8 Open Position: Use this position to run the unit. Closed Position: Use this position to service, transport, or store the unit. OS8215 1 2 WARNING: Hand contact with the rotating impeller is the most common cause of injury associated with snow throwers. Never use your hand to clean out the discharge chute. 1 Figure 9 OS8235 1. Snow Clean-Out Tool Discharge Chute Crank Skid Shoes Discharge Chute Crank Skid Shoes SERVICE AND ADJUSTMENTS on page 18, or repair before operation. Rotate the chute with the discharge chute crank handle. IMPORTANT: DO NOT force frozen chute controls. If frozen, take to warm place until controls are free. Axle Lock Pin (Figure 10) Use the axle lock pin to lock or unlock the right or left wheel. Lock both wheels to increase traction; unlock one wheel to allow for easier turning of the unit. NOTE: Unit will not drive with both wheels unlocked. Figure 10 Wheel Unlocked Wheel Locked Axle Loc...
Эта инструкция также подходит к моделям:Снегоочистители - Sno-Tek 24 920400 (7.68 mb)
Снегоочистители - Sno-Tek 26 920401 (7.68 mb)