Оценок - 3, средний балл: 3.7 ( )

Производитель: Cannon Размер: 1.21 mb Название файла: Язык инструкции:

The thrust bearing spring should be oriented where the narrow end is toward the bearing. Slide the bearing with races and spring over the ratchet shaft. Then, carefully thread the crank handle onto the shaft and continue turning the handle clockwise until the clutch is fully tightened NOTE: Place your fingertip on the edge of the bearing and races. This allows the crank to be threaded more easily until the spring puts resistance on the clutch pad. Thrust Bearing Spring Crank Handle Races Terminating the Downrigger Cable Cable Unwind about 2 feet of cable Rubber Cushion and thread the cable through the rubber cushion. Attach to terminator. Snap & Swivel Tip: A set of pliers with wire cutters is recommended for this part of setup. TIP: Use only straight cable, not kinked. Lead cable into Tighten cable HOLE A. by squeezing Pull six inches of terminator until cable through. it snaps shut. Thread cable HOLE A Then pull at top through swivel, and bottom then up into until drawn bottom of the tight. Make terminator. sure that the cable Lead cable out of threads in HOLE B and into groove of HOLE C. Push the hook. the cable until its end touches the Swivel inside of the terminator hook. Cannon Uni-Release The Cannon Uni-Release attaches directly to the downrigger weight. Attach fishing line to the clip at the end of the release, and then click through a series of increasing tension settings. The release can be used with any test line on salt or fresh water and may be adjusted from 2 to 22 pounds of grip tension on the line. To change line release tension, turn tension knob to (+) to increase or (-) to decrease. Tension also may vary according to where the line is placed in the grips. Higher tension is on the line if it is set back toward the hinge, and lower if set closer to the opening. To open the release, spread the release arms with thumb and forefinger applying pressure to the sides. Examine the top of the terminator and note the order shown in the detail to run cable. CABLE IN CABLE IN CABLE OUT Slide the cushion over the top of the terminator and give it a test pull. The cable is set to attach a Cannon Trolling Weight. Close Tension Open Adjust Fishing Line Open Gripper Pads 9 TERMINATOR & LINE RELEASE 10 ATTACHING THE ROD HOLDER 10 ATTACHING THE ROD HOLDER Attaching the Rod Holder The positive lock rod holder incorporates a locking disk that allows the rod holder to be aligned in 15 degree increments. Slide the rod holder tube into the clamp to the desired position within the recommended area (see below). Be sure the angled shoulders are facing up. Place the locking disk into the mating recess of the frame. Slip the clamp arms in place where the obround tab on the disk fits into the slot on the clamp. Slide the star washer between the arm of the clamp and the frame. Place the flat washer onto the bolt. Then insert the bolt with washer through the clamp by entering the disk, going through the frame, the star washer, and out the other side of the clamp. Tighten the nut to secure the rod holder. Reposition the rod holder by loosening the nut and adjusting the tilt. Single Rod Holder Assembly Recommended Area to Clamp Rod Holder Star Washer Placement Angled Shoulder CAUTION: This rod holder is intended for use of up to 30 lb. test line only, and is not recommended for use with any tackle IGFA rated higher than 30 lb. A safety strap (not included) is recommended for all applications. The rod holder assembly is not warranted when used with tackle above 30 lbs. Equipment placed in the rod holders and the loss thereof is the responsibility of the user and is in no way warranted by JOHNSON OUTDOORS, INC. Mounting must be in accordance with the above instructions and diagram to be warranted. Dual Rod Holder Assembly Operating Your Downrigger After mounting the Cannon downrigger to your boat, release some line from your rod and reel so that the lure is anywhere from 5 to 100 feet behind the boat, this is called drop back. Attach the fishing line firmly into the line release. Lower the weight to the desired depth as indicated on the depth meter. Place the fishing rod in the rod holder and reel up the slack so that your rod has a slight bend in it. When a fish strikes the lure, the line will separate from the release. Then you will be free to fight the fish and bring it in on your rod and reel. Lowering the Weight You can lower the trolling weight at a controlled rate by turning the crank handle gently counterclockwise (away from the boom). Depending on how far you turn, you can let your trolling weight descend as fast or as slowly as you wish. Turn the crank handle clockwise (toward the boom) until it you hear a click to stop the weight. This gives you control to let it plunge rapidly or sink slowly to a predetermined trolling depth. With multiple downriggers, you could start all your weights creeping down, one at a time, and then stop them each in turn. Raising the Weight Turn the crank handle clockwise (toward the boo...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: