Оценок - , средний балл:
(
)
)
Производитель: Harbor Freight Tools
Размер: 647.82 kb
Название файла: 96529.pdf
Язык инструкции:
Документ загружается, подождите пожалуйста
 |
Документ загружается, подождите пожалуйста
Фрагмент инструкции
Fire hazard! This product IS NOT flame retardant. Do not smoke near or 4. introduce flames near this product. This product cannot support the weight of people or any objects. Do not sit or 5. stand on this product. Do not place any objects on this product. Do not use in windy conditions.6. Do not allow water or debris to accumulate on top of the Shelter.7. Do not allow children to play with this product.8. Avoid a dangerous environment. Do not use this product near high voltage elec9. trical lines. When servicing use only identical replacement parts.10. Use the right equipment. Do not use this product except for that which it is in11. tended. Store idle equipment indoors. When not in use, this product should be stored 12. indoors in a clean, dry, safe location out of reach of children. Check for damaged parts. Before each use, this product should be carefully 13. checked to determine that it will operate properly and perform its intended function. Check for alignment of parts, binding of parts, breakage of parts, mounting, and any other condition that may affect its operation. Maintain labels and nameplates on this product. These carry important safety 14. information. If unreadable or missing, contact Harbor Freight Tools for a replacement. The warnings, precautions, and instructions discussed in this instruction manual 15. cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Save these instructions. Specifications Material Formed steel tubing / Camouflage polyester with dark olive green draw strings and hook and loop closures. Main Tube Dimensions 5/8” O.D. x 58-11/16” Long Recommended Tree Trunk Diameter 9-4/5” to 15-11/16” Rear Tree Support Bar Dimensions 18-1/2” Wide x 6” L x 3/16” Thick Cross Tube Dimensions 5/8” O.D. x 24” Long Arm Tube Dimensions 5/8” O.D. x 22-1/2” Long Side Tube Dimensions 5/8” O.D. x 14-1/8” Wide x 48-1/2” Long Overall Dimensions 60” Long x 48” Wide x 81-1/2” High (Includes roof and side walls fully assembled) Net Weight 16 lb. Unpacking When unpacking, check to make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. Set Up Instructions Read the entire Important Safety Instructions section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram on page 7 of this manual. Set the Main Support Frame (3) and the two pieces of Side Frame (2) on a dry, 1. flat, level surface. (See Assy. Diagram.) Unfold the two Hinging Braces (4) on the Main Support Frame. Then attach the 2. Support Brace (5) to the Main Support Frame using two Bolts (9), two Flat Washers (15), and two Lock Nuts (16). (See Assy. Diagram.) Insert the two Side Frames (2) into the Main Support Frame (3), and fasten the 3. two Side Frames to the Main Support Frame using two Bolts (14), two Flat Washers (15), and two Lock Nuts (16). (See Assy. Diagram.) Affix the Strips of the Fabric Cover (1) around the edges of the Main Support 4. Frame (3) and Side Frames (2) with the Draw Strings and Hook and Loop Closures. (See Assy. Diagram.) REV 09a Use the remaining Draw Strings to secure the rest of the Fabric Cover (1) to the 5. Main Support Frame (3) and Side Frames (2). (See Assy. Diagram.) Remove the Bolt (11), Flat Washer (7), and Wing Nut (10) from one end of the 6. Rear Cross Bar (12). (See Figure A and Assy. Diagram.) With assistance, position the Hunting Shelter against the trunk of a tree. Adjust 7. the Rear Cross Bar (12) to fit firmly against the tree trunk. Then secure the Hunting Shelter to the tree trunk by re-installing the Bolt (11), Flat Washer (7), and Wing Nut (10) on the Rear Cross Bar. (See Figure A and Assy. Diagram.) NOTE: 8. Make sure both Bolts (11), Flat Washers (7), and Wing Nuts (10) on the Rear Cross Bar are firmly tightened.(See Figure A and Assy. Diagram.) Attach the Side Cover (18) to the Side Frame (2) using the 8 Hooks (17). See 9. diagram on page 7. Adjust the height of the shelter so the Side Cover touch the ground.10. REAR CROSS BAR (12) BOLT (11) FLAT WASHER (7) WING NUT (10) FIGURE A See cover page photo. Attach the bottom of the Side Cover (18) to the ground using the U-Shaped land11. scape Staples (19). See Parts List and Assembly Diagram on page 6 and 7. REV 08e Maintenance And Servicing Damaged equipment can fail, causing serious personal injury. Do not use damaged equipment. If a problem occurs, have the problem corrected before further use. Inspection, maintenance, and cleaning BEFORE EACH USE,1. inspect the general condition of the Hunting Shelter. Check for loose screws, misalignment or binding of parts, cracked or ...