Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Door trim moulding release buttons OVEN DOOR: 1. Open the door fully through 180°. 2. Remove the left hand door top trim by pressing the release button that is situated between the inner and outer glass panels, at the top of the door. 3. While holding the weight of the inner glass panel, repeat the procedure for the right hand door top trim. 4. When replacing the door inner glass panel, ensure that it is held in place by the top and bottom door trims so that it cannot fall out and that the printing on the glass is readable from the face nearest to the oven. NEVER OPERATE THE COOKER WITHOUT THE DOOR INNER GLASS IN POSITION. Care and Cleaning Oven Linings The oven side linings are coated with a special enamel which has a continuous cleaning action. The higher the oven temperature the more effective the action. In most cases this cleaning operation will proceed during normal cooking. However, if roasting is done frequently, or high temperatures are not used regularly, it may be necessary to run the oven empty at Mark 8 for about two hours. If desirable, they can be washed with warm soapy water followed by a rinse. Replacing the battery The battery is not covered by the guarantee. Use an alkaline AA battery. The battery holder is located in the plinth panel below the oven door. Open the oven door fully. Press the tag on the left hand side of the battery holder/cover and withdraw it just enough to get access to the battery. Fit the new battery with the end marked “+” on the same side of the battery holder as the red lead. Replace the battery holder by pushing it firmly into the hole in the plinth. Care and Cleaning COOKER FINISH CLEANING METHOD Vitreous Enamel Hotplate, burner caps, grill Cloth wrung out in warm soapy water. Stubborn pan, oven base and rear, stains can be removed with a cream paste, inside of grill compartment, liquid cleaner or by rubbing with fine steel wool control panel. soap pads. Check that the cleaning agent is approved by the Vitreous Enamel Development Council. Paint Plinth, Fascia bottom trim, Wash with a cloth wrung out in warm soapy water side panels, Lid trim, Rear only. end caps DO NOT USE ABRASIVES. Aluminium Hotplate burner bodies Similar to paint cleaning above. Use a nylon brush to remove any cleaning materials, water or dirt from the hotplate burners. Chromium Plating Oven shelves, grill pan grid, Wipe with a cloth wrung out in warm soapy water. grill pan handle support A fine steel wool soap pad or a chrome or stainless steel cleaner may be used. Plastic Grill pan handle, door Wipe with a cloth wrung out in warm soapy water. handles, control knobs Stubborn stains can be removed with a cream cleaner. Glass Lid, Door Wash with cloth wrung out in warm soapy water only. Do not use ABRASIVES. Polish with a dry cloth or kitchen towel. NOTE: To ensure rapid lighting of the hotplate burners every time they are used, the electrodes must be kept clean and dry. Remove any food spillage or cleaning materials from the electrode using a small nylon brush such as a tooth brush. Something Wrong With Your Cooker Before calling a Service Engineer, please check through the following lists. THERE MAY BE NOTHING WRONG. Problem Check Slight odour or small amount of smoke when grill / oven used first time This is normal and should cease after a short period. Oven cooks too fast or too slow Check that the gas mark and shelf positions are as recommended in the Oven Cooking Charts. However, it may be necessary to increase or decrease the recommended setting slightly to suit your taste. Ignition does not work. Burner ports Ignitor Oven burner Grill burner If all burners fail to ignite: Check that sparks appear at the burners; a clicking noise should be heard. If not Check the battery, or fit a known good battery to the product. Batteries are not covered by the guarantee. The battery is easily changed - see the section on battery replacement. (An “AA” size alkaline battery should be used). If only one burner fails to ignite: Check that the burner is dry and that spillage of food or cleaning fluid remains are not affecting the ignitor or burner ports. Clean away any debris with a dry nylon brush such as an old toothbrush. If a wire wool pad has been used for cleaning around the burner ensure the ignitor is free from any stray strands. Any water on the burner should be dried with a cloth or kitchen towel. Burner ports Ignitor Hotplate burner. On hotplate burners make sure that all the burner parts are correctly seated on the burners. Burner ports Ignitor Installation Instructions Gas Safety (Installation & Use) Regulations Location Provision for Ventilation Prior to installation, ensure that the local distributions (nature of the gas and gas pressure) and the adjustment conditions are compatible. The adjustment conditions for this appliance are stated on the data badge which is fitted on the rear panel. This appliance is not designed to be connected to a combustion products evacuation device. It must be i...